Please draw the picture of this problem and solve it. A uniform rigid disk has mass M and radius a, and a uniform rigid rod has mass M' and length b. The rod is placed along the axis of symmetry of the disk with one end in contact with the disk. Find the forces necessary to pull the disk and rod apart.

Please draw the picture of this problem and solve it. A uniform rigid disk has mass M and radius a, and a uniform rigid rod has mass M' and length b. The rod is placed along the axis of symmetry of the disk with one end in contact with the disk. Find the forces necessary to pull the disk and rod apart.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

The uniform bar of weight W is held in equilibrium by the couple C0. Find C0 in terms of W, L, and .
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the cable.
A uniform rigid disk has mass "M" and radius "a", and a rigid uniform rod has mass "m" and length "b". The bar is located along the vertical axis of symmetry of the disk with one end in contact with the disk. Find the force required to separate the bar from the disk. The bar is on the disk.
Q3/ A shaft has three eccentric of mass 1 kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20, 30 and 20 mm and their angular positions are 120 apart. If the shaft is balanced by adding two niasses at a radius of 70 mm and at a distance 100 mm from the central plane of the middle eccentric, find the amount of the masses and their angular positions.
Q3/ A shaft has three eccentric of mass 1 kg cach. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20, 30 and 20 mm and their angular positions are 120° apart. If the shaft is balanced by adding two masses at a radius of 70 mm and at a distance 100 mm from the central plane of the middle eccentric, find the amount of the masses and their angular positions.
The tractor shovel shown ,carries a 530 kg load that has its center of mass at HH. The shovel’s dimensions are: a = 51.0 mm, b = 204 mm, c = 306 mm, d = 102 mm, and e = 357 mm. Find the reaction force at E(Ex and Ey). Assume that the positive direction of the x and y axes is to the right and upward, respectively.
2.5 m 3.0 m 4000 N m 2.5 m 300 N 2 m 30° A smooth and weightless rod is subject to a force on one end and a moment at its mass center. If the Uniform rod is supported at multiple points as shown in the picture, find the reaction forces at these supports. Assume that the rod is supported at point A by a smooth wall and at B and C either at the top OR bottom by rollers. On your answer sheet provide the FBD and all your calculations.
In the mechanism shown, find the force P and all reaction forces. Ignore weight forces and friction
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
3. The tasty fish pictured above has a mass of 1100 kg and is hanging from a cable attached via a 4 m long, 600 kg beam that can pivot at its base to a 6 m tall pole. The center of mass of the beam is at a point 1/3 of the way between its base and end. Find the tension in the cable between the beam and the pole.
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs