5 and 6 Problem # 5) Given the following (steady-state) AC circuit:VsZ₁40-j30Ohms+ Automatic Zoom50+j120Ohms Z₂Z1 24-110OhmsProblem #6) Repeat problem #5, but use the new source voltage: V=2402-90° voltsProblem #7) Given the following (steady-state) AC circuit:Isj22Ohms50+128OhmsVs = 240/180° voltsDetermine the complex power consumed byEACH of the load impedances, S1 and S2, aswell as the total complex power producedby the source, Ssource.MacBook ProV = 482-30° voltsDetermine the real power P, that is consumed only by the impedance labeled Z1 in the circuit.Print

In this question We need to determine the complex power of the each load and total complex power…

Problem # 5) Given the following (steady-state) AC circuit: Vs 40-j30 Z₁ Ohms 50+j120 Ohms Z₂ = 240/180° volts Determine the complex power consumed by EACH of the load impedances, S, and S2, as well as the total complex power produced by the source, Ssource. Problem #6) Repeat problem #5, but use the new source voltage: V = 240Z-90° volts

Problem # 5) Given the following (steady-state) AC circuit: Vs 40-j30 Z₁ Ohms 50+j120 Ohms Z₂ = 240/180° volts Determine the complex power consumed by EACH of the load impedances, S, and S2, as well as the total complex power produced by the source, Ssource. Problem #6) Repeat problem #5, but use the new source voltage: V = 240Z-90° volts

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
The ripple factor for pure dc is Answer:
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
Q5)-a)For this figure shown below the phase relationship between the sinusoidal waveform Of this set. -10sin(wt+80) V=15sin (wt+40) Q5)-b) for this circuit find the max energy if XL=100 Vm-300v,L=0.3H V= Vm Sinwt
Ac - 100 VrmsR1 - 1kR2 - 500Rload - 1kCapacitor - 2uF Q1. How much is the capacitor voltage lagging from the AC source
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.