PROBLEM O1: A loadP compresses the bronze core, brass, and steel shell as shown in the figure, which have a length L=5.0". Knowing that moduli of elasticity of the bronze, brass and steel are EBR=14.5x106 psi, EB=15x106 psi and Es=30x106 psi, respectively. The diameters are D1=0.24", D2=0.27", D3=0.34", D4=0.37", and Ds=0.40". Determine the load P that will shorten the assembly by 0.004 in. P -STEEL SHELL BRASS TI || BRONZE CORE || || D D D || ||

PROBLEM O1: A loadP compresses the bronze core, brass, and steel shell as shown in the figure, which have a length L=5.0". Knowing that moduli of elasticity of the bronze, brass and steel are EBR=14.5x106 psi, EB=15x106 psi and Es=30x106 psi, respectively. The diameters are D1=0.24", D2=0.27", D3=0.34", D4=0.37", and Ds=0.40". Determine the load P that will shorten the assembly by 0.004 in. P -STEEL SHELL BRASS TI || BRONZE CORE || || D D D || ||

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
Given : Steel: A = 600mm2 ; E = 200 GPa Bronze : A = 900mm2 ; E = 83 GPa Show the complete solution and FBD
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
1. Find the Normal Stresses experienced by the Steel, Aluminum, and Bronze section of the given body. The value of P is 3000 pounds and the cross-sectional area of the rod is equal to 0.5 squared inches. Steel Aluminum Bronze 4P = 12k P 3k
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to 11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. 14 in. 18 in. ਕਰ Bronze A = 2.4 in² E-15 x 105 psi a = 12 x 10-6/"F Aluminum A = 2.8 in² E = 10.6 x 105 psi a = 12.9 × 10-5/"F
A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Round off your final answer to 2 decimal places] Steel Brass A = 480 mm A = 650 mm? Aluminum A = 320 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Est = 200 GPa Ebr = 100 GPa Ecu = 120 GPa %3D ast = 12(10-6)/°C abr = 21(10¬6)/°C acu = 17(10-)/°C %3D Acu = 515 mm² |Ast = 200 mm? Abr = 450 mm² %3D 300 mm- 200 mm 100 mm O -0.0058mm O 0.0165mm O -0.0165mm O 0.0058mm
O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze A=450 mm2 A=600 mm Aluminum Steel A=300 mm 2 Compute the max. value of P that will not exceed a stress of E-83 GPa E=70 GPs E=200 GPa aluminum of 90 MPa. 600 mm 1,000 mm 800 mm 3Compute the maximum value of P that will not exceed a stress of steel (3) of 140 MPa.
A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the results shown in Table P3.27. Using a computer spreadsheet pro- gram, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel and the deformation corresponding to a 150-kN load. TABLE P3.27 Load, kN Deformation, mm 54 0.084 163 0.168 284 0.336 330 1.428 366 3.360