Q1) A single-phase AC voltage controller is connected to an inductive load with a resistance of 10 and load impedance angle of 45°. The input ac voltage is 230 V at 50 Hz. (a) Draw the load voltage waveforms and derive an expression for the rms load voltage. (b) Determine the maximum load voltage, maximum load current, and range of delay angie for which the load voltage does not change.

Q1) A single-phase AC voltage controller is connected to an inductive load with a resistance of 10 and load impedance angle of 45°. The input ac voltage is 230 V at 50 Hz. (a) Draw the load voltage waveforms and derive an expression for the rms load voltage. (b) Determine the maximum load voltage, maximum load current, and range of delay angie for which the load voltage does not change.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415V through a delta-star transformer as shown in the Figure. The load consists of large inductance to render a level load current of 60A at 300V. Assuming voltage drop across the power device to be 0.7V, compute the following: i) Rms value of secondary phase voltage and current; ii) Rms value of primary phase voltage and current3; iii) Transformer power rating in kVA and transformation ratio; iv) Device ratings. 本の。本の本の Load 本の。本。本の。 Figure
Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
A step-up chopper has input voltage of 220 V and output voltage of 660 V. If the conducting time of the IGBT based chopper is 100 micro- sec, then duty cycle will be a. -0.66 b. 0.7 c. 1.66 d. 0.66
For the single phase half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 50 Hz. The load resistor is 5ohm. Determine (a) the average load current, (b) the average power absorbed by the load and (c) the power factor of the circuit.
a. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 2 load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 N. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz.
A step down de chopper is connected to an R5 2 and L-10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, lo and the peak to peak ripple current as an absolute value and as percentage of de value.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
Describing the concept of discontinuous conduction mode in power converters, how does continuous conduction mode differ?Make a DC-DC converter circuit that operates in discontinuous conduction mode.
(B) / For a step-down DC-DC converter (chopper), if the DC input voltage =150V, load resistance =102. Take a voltage drop of 2V across chopper when it is on. For a duty cycle of 0.5, calculate: (i) Average and rms values of output voltage, (ii) Chopper efficiency.
1) The current and voltage waveforms given in the figure on the right.power electronics converter to which the shapes belongDraw the circuit. The stress on the load andThe relations for the average value of the current are obtained.please. 2) Positive half wave of AA voltage transferred to the loadfixed negative half wave is a controllableDraw an AA phase control circuit. Pure ohmic load and ?output current and voltage for a trigger angle such asGive the waveforms. 0 <? <pi