Q4/A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a riding tractor. A 5-hp single-cylinder engine is used. At most, 60 percent of this power is transmitted to the belt. The driving sheave has a diameter of 6.2 in, the driven, 12.0 in. The belt selected should be as close to a 92-in pitch length as possible. The engine speed is governor-controlled to a maximum of 3100 rev/min. Select a satisfactory belt and assess the factor of safety and the belt life in passes.

Q4/A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a riding tractor. A 5-hp single-cylinder engine is used. At most, 60 percent of this power is transmitted to the belt. The driving sheave has a diameter of 6.2 in, the driven, 12.0 in. The belt selected should be as close to a 92-in pitch length as possible. The engine speed is governor-controlled to a maximum of 3100 rev/min. Select a satisfactory belt and assess the factor of safety and the belt life in passes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
Machine design A 60-hp four-cylinder internal combustion engine is used to drive a medium-shock brickmaking machine under a schedule of two shifts per day. The drive consists of two 26-in sheaves spaced about 12 ft apart, with a sheave speed of 400 rev/min. Select a Gates Rubber V-belt arrangement. Find the factor of safety, and estimate the life in passes and hours?
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the height in m to lift the load vertically up sufficient to give 33.5 m inclined belt length. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, plain chain drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
Q1/ A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 9 ft. The angular speed of the small pulley is 1750 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, Fla, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a multiple v-belt drive which is powered by a compressor-stator motor with speed 1300 rpm. The center distance must be between 30 to 40 inches and the available driver sheave diameter iS 14 inches. Recommend a multiple v-belt drive that respects the following condition stated.
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear