Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the clutch equal to 106mm. The cone has a face angle of 12°and the engagement factor is 1.5. If the mean normal pressure on the clutch face is not exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force necessary to engage the clutch is 1796N. Requirements: 1) The mean diameter of the cone clutch. 2) The developing power. 3) Complete the construction drawing by showing all the details.

Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the clutch equal to 106mm. The cone has a face angle of 12°and the engagement factor is 1.5. If the mean normal pressure on the clutch face is not exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force necessary to engage the clutch is 1796N. Requirements: 1) The mean diameter of the cone clutch. 2) The developing power. 3) Complete the construction drawing by showing all the details.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) A multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of thecontact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of "0.1". The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.
Q8 A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters ofthe contacting surfaces are 200 and 250 mm respectively. The coeffi cient of friction is 0.1 and themaximum pressure between the contacting surfaces is limited to 0.4 N/mm. Assuming uniform weartheory, calculate the required force to engage the clutch and the power transmitting capacity at 720rpm.
Q3 /A multi - plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer radii for the plates are to be 50 mm and 100 mm respectively. The maximum axial spring forces is restricted to 1 kN. Answer the following questions 1- The necessary number of pairs of surfaces is u= 0.35 assuming constant wear. 2- The necessary number of pairs of surfaces is constant pressure. u= 0.18 assuming 3- The axial force 4- Percentage increase in forces is
Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the intensity of pressure is not to exceed 127 kN/m?, find the power in kW transmitted at 500 r.p.m, if the outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction as 0.3.
Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2
Q. A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficients of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
Q2/ A dry single plate clutch is to be designed for an autontotive vehicle whase engine is ated to give 100 &W at 2400 r.p.M. and marimum torque 500 N-m. The outer radus of the friction plate is 25% ore than the inner radius, The intensity of pressure berween the plate is not to exceed 0.07 N/mm. The coefficient of friction may be assamed egual t0 0.3 The helical springs reguired by this cluich to provide axial force mecessary to engage the clutch are eight. If cach spring has stiffness equal to 40 N/mm, derermine the dimensions of the friction plate and initial compression in the springs
25 Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm2 ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
Example: An automotive single-plate clutch with twe of friction Surfaces, transmits a 300 N-m to- pairs rque at 1500 rp.m. The inner and outer diameters of the friction disck are 170 and 270 mm The cofficient of friction is 0-35. The normal for- ce on the friction Surfaces is exerted by nine helical Compre ssion springs, so that the clutch is always engia- ged. The clutch is dis engaged when the external force Further Compresses (5) and the number of ac Five Coile are (6) The are made of patented and Cold-drawn steel respectively. the springs. The spring index is Springs wires of minimum tensile Stmength (MTS) (N/mm?)as Wive dia. 1 1-21-4 1.6 1-8 2 2.53 3.6445567 MTS, 1900 i2601817e0175017201640 1570 I510 1480 440 139013201260 NI mr The permissible shear stress for the wire is 30%. of the ultimate tensile strength, and (G-81370 Nimn). Design the springs and specily their dimensisns. Use this relatian to obtaine to the total normal fore required to transmit the torque. F= 4T where Dis…