Q6. Figure Q6 shows an LCR resonant filter circuit. If the quality factor Q is large enough Vin Vout Figure Q6: LCR filter then the frequency transfer function (in terms of the circular frequency w) of this filter can be approximated, 1 H(@) 1+ 2JRC(w – wo) Taking L=1 mH, C=25 nF and R=2 k2. (a) Calculate the expected resonant frequency, vo, of this filter (in kHz). (b) Find the -3 dB points (in power) for this filter and hence determine its bandwidth. (c) Determine the value of the quality factor Q for this filter. (d) Using the properties of Fourier transforms and the tabulated selected transforms, determine the impulse response function corresponding to this transfer function. (e) Sketch the form of the real part of the impulse response function. (f) A bandpass filter, such as the one described above, is usually inserted after a chopper or rectifier modulator: explain why and identify the requirements on the resonant frequency and the bandwidth of such a bandpass filter.

Q6. Figure Q6 shows an LCR resonant filter circuit. If the quality factor Q is large enough Vin Vout Figure Q6: LCR filter then the frequency transfer function (in terms of the circular frequency w) of this filter can be approximated, 1 H(@) 1+ 2JRC(w – wo) Taking L=1 mH, C=25 nF and R=2 k2. (a) Calculate the expected resonant frequency, vo, of this filter (in kHz). (b) Find the -3 dB points (in power) for this filter and hence determine its bandwidth. (c) Determine the value of the quality factor Q for this filter. (d) Using the properties of Fourier transforms and the tabulated selected transforms, determine the impulse response function corresponding to this transfer function. (e) Sketch the form of the real part of the impulse response function. (f) A bandpass filter, such as the one described above, is usually inserted after a chopper or rectifier modulator: explain why and identify the requirements on the resonant frequency and the bandwidth of such a bandpass filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A very common problem in instrumentation is that of interference of the telemetry that is to be measured. One of the primary sources of the interference is the power line. This is particularly true for high impedance circuits. Another path for this noise is ground-loops. One possible solution is to use a notch filter to remove the 50HZ component. Design a suitable notch filter for this purpose.
(b) In a filter, explain what happens at the cut–off frequency.
Find theoretical expressions for the transfer function and cutoff frequencies of the circuit in figure 1. ( RL = 4.2k other values is up to you)
Explain why it is necessary to add capacitor in Low pass filter draw circuit diagram and explain w.r.t combination of Capacitor and RL.
What is the function of a low pass filter? Draw a diagram of a simple low-pass filter using a capacitor and a resistor.
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
Identify the reason for a nonsinusoidal signal being distorted when it passes through a filter. -The distortion occurs because harmonics are removed or rejected, leaving a different waveshape. -The distortion occurs because harmonics are synchronized, leaving a different waveshape. -The distortion occurs because the signal is modulated, leaving a different waveshape. -The distortion occurs because harmonics are added in the filter, leaving a different waveshape.
What is the transfer function of a filter? Describe how the transfer function of a filter can be determined using laboratory methods.
In the filter shown in figure 8 the ratio between the output AC voltage Vout and input voltage Vin is given by Vout R wCR (1) R+ j(wL – 1/(wC)) Vin R+ j(w?LC – 1) - -
What is a bandpass filter? How is its bandwidth defined?
what is the main differences between ideal filters and real filters.
What is the definition of resonant frequencies, cut-off frequencies, bandwidth, andquality factor of series and parallel RLC circuits.And how do you determine the circuit conditions at the resonant and cut-off frequencies. (Answer in long paragraph form)