Select the equipment that is typically fitted in each of the following locations and mechanical equipment: 23. Building Air Conditioning handling Unit (AHU). 24. Basement parking Ventilation a) In line pumps b) Exhaust fans c) Vane axial fans d) Blowers e) Centrifugal fans f) Propeller fans g) Squirrel cage fans h) Compressor 25. Water Treatment Aeration tank 26. Fire Fighting Systems water supply 27. Car Air Con Condensing Unit 28. Building rest rooms 29. Genset cooling system 30. Jack hammer

Select the equipment that is typically fitted in each of the following locations and mechanical equipment: 23. Building Air Conditioning handling Unit (AHU). 24. Basement parking Ventilation a) In line pumps b) Exhaust fans c) Vane axial fans d) Blowers e) Centrifugal fans f) Propeller fans g) Squirrel cage fans h) Compressor 25. Water Treatment Aeration tank 26. Fire Fighting Systems water supply 27. Car Air Con Condensing Unit 28. Building rest rooms 29. Genset cooling system 30. Jack hammer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Describe the following HVAC systems. a) All-air systems b) All-water systems c) Air-water systems Graphically represent each system with a sketch.
Should the bulb of the thermostatic valve be positioned just below the inlet duct? aspiration? b) No a) Yes The hot gas defrost method uses heat from: c) make-up water b) electrical resistances a) hot compressor refrigerant When the refrigerated space has been allowed to heat up to a temperature higher than the desired one, the system must go through a process outside the normal design conditions to regain its normal operation, this process is called: c) hot drop a) overheating b) subcooling
Qn) A)What is thermocouple? Explain measurement system using Thermocouple with a neat schematic sketch. Draw the characteristics and write its different types with properties.
It is feasible to reuse the heat from the condenser and use it for domestic heating. a) Yes b) No This type of open compressor can have more than one speed. b) directly driven a) belt driven c) hermetic
Q3) give the short answer for the questions below; a) Growth the frost over evaporator surface lead to decrease freezer temperature. b) Using copper tube type-k in the shell and tube heat exchanger c) Make a vacuum pressure for the vapour compression cycle (refrigeration system) before charging with refrigerant (give the value of vacuum pressure) d) Age of compressor depending on the number of turn-on and turn- off, not depended on the working time. e) Skin type condenser favorite more than other type of static condenser in the chest freeze f) Draw the relationship between time and difference temperature for the conventional refrigerator cycle control and inverter refrigerator electrical behavior control.
In the rotameter (gas flow sensor), rotor friction is greatly increased by water condensation and therefore when mounted on a ventilator or anesthesia machine; insertion is recommended in:A) The inspiratory pathway.B) The expiratory route.C) The escape route.D) B and C
|Qout| > |Wcycle| in (mark all that apply): a) Refrigeration cycle b) Power cycle c) Heat pump cycle
The following air streams mix in a building’s HVAC system upstream of the HVAC heating unit: 1,600 CFM outdoor air at 35°F and 70% RH mixes with 3,500 CFM of return air at 70°F and 40% RH. Assume the HVAC runs for 1 minute, so CFM is the same as cubic feet. a) What are the temperature and RH of the combined air stream? b) How much energy (units of BTU) does the HVAC heating unit need to add to the combined air stream to condition it to 80°F and 60% RH? c) If the conditioned air stream from the heating unit then mixes with 28,000 CFM of air at 70°F and 40% RH provided to the building from another source, what are the combined temperature and RH of the air in the building?
5)which one of the componets is used in pneumatic systems only? a)counter balance valve b)Quick exhaust valve c)AND valve d) Unloading valve 6)An air regulator can be mounted at any position? Select: true or false 7)Filter are use in: a)None of these b)Hydraulic systems only c)fluid power systems d)pneumatic systems only 8)which one of the componets is used in Hydraulic systems only? a)counter balance valve b)Quick exhaust valve c)AND valve d) Unloading valve 9)in a Hydraulic system,the filter can be located in supply and return line? Select : True or false 10) An AND valve can allow flow alternatively from its inlets. Select : true or False
##What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?
Excluding lines, which of the following components are required to make simple hydrolic system?  A) Reservoir, pump, filter & regulator. B) Reservoir, ACOV, pressure relief valve & actuator. C) Reservoir, pump, selector valve & actuator.
a) Define the "force exerted by air pressure" in a pneumatic cylinder? b) Differentiate double acting cylinder and single acting cylinder. Discuss advantages and disadvantages? c) What pneumatic ports are designated as exhaust ports in a 5/2-way pneumatic valve? Explain the indication of 5/2-way'. d) What are the 3 main components of an air service unit? Show the symbols. e) Calculate the diameter of pneumatic double acting cylinder (in inch) to drive a mechanism The force/thrust developed by a piston due to air pressure is 20lbs. The return force is negligible. The working pressure is 100psi.