Steel bar with dimensions with (10mm and 10mm) subjected to axial load of * 2000N. Determine the stress
Q: A steel bar of 40 mm x 40 mm square cross section is subjected to an axial tensile load of 200 kN.…
A: Given , dimensions of the steel rod =40mm×40mm Axial tensile load, P=200kN=200×103N Length of the…
Q: A round steel tension member 40 in. long is subjected to a maximum load of 6,500 lbf. (a) What…
A: Given:- Length : 40 in Load : 6500 lb
Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…
A:
Q: QUESTION 3 A 300mm x 100mm channel section is used as a short vertical column. The column is to…
A: given; →dimension ; (b*d)=300mm*100mm→width(b)=300mm→depth(d)=100mm→compressive load (P)=500KN…
Q: H.W: 1 rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the…
A:
Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…
A:
Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter…
A: Given: Tensile load P=40 KN Diameter of the rod D=40 mm Area of the road A=π4D2…
Q: An axial load of 5000 kN is to be supported by short reinforced concrete column 400 mm x 500 mm with…
A: Given: The axial load, P = 5000 kN The area of the column, Ac = 400 mm x 500 mm The length of the…
Q: A steel plate subjected to a force of 3 kN and fixed to a vertical channel by means of four…
A: Given data: Force F=3 kN Yield Strength Syt=380Nmm2 Factor of safety FOS=2 Diameter of shank d=?
Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…
A:
Q: The one end of a hollow square bar whose side is (10+N/100) in with (1+N/100) in thickness is under…
A:
Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…
A:
Q: For the assembly shown, determine the displacement of point B and D as the load of 50KN is applied…
A: Given: load on point D→P=50 KN Length of BD=1m Length of AB=2m Let force in the rod BC=FBC now…
Q: A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when…
A: (a) Diameter of rod = 50 mm Area (A) = πd24Area (A) = 3.14 x 0.0524Area (A) = 0.0019625 m2…
Q: 210. An aluminum tube is fastened between a steel rod and a bronze rod as shown in Fig. P-210. Axial…
A:
Q: ick as shown in the ield strength of the 260 N/mm², and plastic moment of nape factor.
A:
Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…
A: Data given- N= 47 So Side of sqaure x = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in…
Q: eter of wires AB and CB. The allowable tensile stress in each wire is 185 Mpa. 30
A:
Q: A 1.5m long composite rod consist of a square cast-iron bar centre of 65mm cross section, reinforced…
A:
Q: The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than…
A:
Q: submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and…
A:
Q: A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress…
A:
Q: A 2024-T4 aluminum tube with an outside diameter of 3.8 in. will be used to support a 36-kip load.…
A:
Q: load of 200 KN. If the length of the bar is 2 m and E = 200 GPa. What will be the elongation of the…
A:
Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…
A:
Q: A steel pipe having the cross section shown is used as a column. Use oy= 250 MPa, t= 6.3 mm, FOS =…
A:
Q: 3 m Load -2 m 3 m The member AC is made from an aluminium alloy and has a rectangular cross section…
A:
Q: a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied…
A: As this is a simple question related to the strength of material subject. As stress formula is given…
Q: Find the Young's Modulus of a brass rod of diameter 25 mm and of length 250 mm which is subjected to…
A: Given, Diameter of rod = d = 25 mm Length of rod = L = 250 mm Tensile load = P = 50 kN = 50 x 103 N…
Q: A Mild Steel wire 5 mm in diameter and 1 m long. If the wire is subjected to an axial tensile load…
A: Given, Diameter of wire = d = 5 mm Length of the wire = L = 1 m = 1000 mm Load = P = 10 kN = 10,000…
Q: ods were stress-free. Determine the load in each rod if W = 51.29 KN. listance into mm. | Figure…
A:
Q: The composite bar is firmly attached to unyielding supports. The initial temperature is 40°F when…
A:
Q: An alloy bar 800 mm long and 200 mm in cross-section is held between two rigid plates and is…
A: Given:- Axial load=200kn Cross-sectional area:-200mm2 To find:- Reaction forces at end and…
Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…
A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…
Q: b) A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If…
A:
Q: A bar having a length of 30 in. is used to support an axial compressive loadof 12 kip, Fig. It is…
A: Given data The compressive load is P=12 kip=12×103 lb From the table of 2014-T6 aluminium alloy, The…
Q: Compare the maximum stress induced into a rectangular plate 100mm long, 50mm width and 10mm…
A: The formulae for stress would be the ration of load to cross section area. The given problem will…
Q: A 100N load is added to the end of circular cross section steel rod that has a length of 0.3m and a…
A: GIVEN DATA- Length of bar L=0.3m Diameter of bar d=0.025m Load P=100N Young Modulus…
Q: A cylindrical rod of diameter 23 mm and length 234 mm is subjected to a tensile load of 57 kN and it…
A:
Q: A steel plate subjected to a force of 5 kN and fixed to a channel by means of three identical bolts…
A: Given data as per question Load =5 KN Yield strength =400 Mpa FOS =3
Q: The steel bar has the original dimensions shown in the figure. It is subjected to an axial load of…
A: When a bar is given tensile stress it tends to get elongated longitudinally, called the longitudinal…
Q: The steel rod in Fig. is to be used to support an axial load of 18 kip. If Est = 29(103 ) ksi and…
A: Given data: The applied load, P = 18 kip. The modulus of elasticity, E = 29 × 103 ksi. The yield…
Q: The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an…
A: Given data: F=50 kN Need to determine the change in its length, the new height at section a-a, and…
Q: 14. A bar of 2 m length, 20 mm breadth and 15 mm thickness is subjected to a tensile load of 30 kN.…
A: Given:- length: 2m breadth: 20mm thickness: 15 mm Load 30 KN
Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…
A:
Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…
A:
Q: 9- Compute the total elongation caused by an axial load of 100 kN applied to a flat bar 20 mm thick…
A: Find the total elongation caused by an axial load 100 KN applied to a flat bar 20 mm thick ,…
Step by step
Solved in 2 steps with 2 images
- Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPaSolve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
- The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
- An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.A machine member part is subjected to fluctuating stress of σ = ax cos(8nt) The endurance limit of the material is 350 MPa. If the FoS used in the design is 3.5 Find the maximum value of ?PROBLEM: 1 A pair of wheels of a railway wagon carries a load of 50 kN on each axle box, acting at a distance of 100 mm outside the wheel base. The gauge of the rails is 1.4 m. Find the diameter of the axle between the wheels, if the stress is not to exceed 150 MPa. 50 kN 50 kN 100 mm 1.4 m 100 mm D Rc Rp
- The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take σ_all=243ksi for pin material.The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1