The cable of the 2000 kg elevator cab in the figure snaps when the cab is at rest at the first floor, where the cab bottom is a distance d= 3.0 m above a spring of spring constant k = 0.19 MN/m. A safety device clamps the cab against guide rails so that a constant frictional force of 4.4 kN opposes the cab's motion. (a) Find the speed of the cab just before it hits the spring. (b) Find the maximum distance x that the spring is compressed (the frictional force still acts during this compression). (c) Find the distance (above the point of maximum compression) that the cab will bounce back up the shaft. (d) Using conservation of energy, find the approximate total distance that the cab will move before coming to rest. (Assume that the frictional force on the cab is negligible when the cab is stationary.) (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Units

The cable of the 2000 kg elevator cab in the figure snaps when the cab is at rest at the first floor, where the cab bottom is a distance d= 3.0 m above a spring of spring constant k = 0.19 MN/m. A safety device clamps the cab against guide rails so that a constant frictional force of 4.4 kN opposes the cab's motion. (a) Find the speed of the cab just before it hits the spring. (b) Find the maximum distance x that the spring is compressed (the frictional force still acts during this compression). (c) Find the distance (above the point of maximum compression) that the cab will bounce back up the shaft. (d) Using conservation of energy, find the approximate total distance that the cab will move before coming to rest. (Assume that the frictional force on the cab is negligible when the cab is stationary.) (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Units

Name: The cable of the 2000 kg elevator cab in the figure snaps when the ca
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The cable of the 2000 kg elevator cab in the figure snaps when the cab is at rest at the first floor, where the cab bottom is a distanced = 3.0 m above a spring of spring constant k = 0.19 MN/m. A safety device clamps the cab against guide rails so

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

A block of mass m = 2.00 kg is attached to a spring of force constant k = 525 N/m as shown in the figure below. The block is pulled to a position x = 5.80 cm to the right of equilibrium and released from rest. k x=0 x=x; (a) Find the speed the block has as it passes through equilibrium if the horizontal surface is frictionless. m/s (b) Find the speed the block has as it passes through equilibrium (for the first time) if the coefficient of friction between block and surface is μk m/s Need Help? Read It Watch It Submit Answer = 0.350.
A block of mass m = 2.00 kg is attached to a spring of force constant k = 555 N/m as shown in the figure below. The block is pulled to a position x, = 4.90 cm to the right of equilibrium and released from rest. x= 0 x= x; (a) Find the speed the block has as it passes through equilibrium if the horizontal surface is frictionless. m/s (b) Find the speed the block has as it passes through equilibrium (for the first time) if the coefficient of friction between block and surface is u, = 0.350. m/s
2. A ball of mass 5.0 kg is suspended by two wires from a horizontal arm that is attached to a vertical shaft, as shown in the figure. The shaft is in uniform rotation about its axis. The rate of rotation is adjusted until the tensions in the two wires are EQUAL. At that speed, what is the radial acceleration of the ball? 0.80 m 1.0 m 0.60 m Ball
A spring is stretched 3 cm by a force of 6 N. Thus, according to Hooke's Law, the spring DO = 200 N. Assume as usual, that r = 0 is the equilibrium position. constant is k 0.03 A mass of 8 kg is now attached to the end of the spring, and it is set in motion with initial position xo = 0 and with initial velocity 10 (m) to the left. ( So, v(0) = -10(m).)
Q3. In the position shown in Figure, the system is in the rest. Cylinder B is considered solid and moves in frictionless bearings. The spring is originally unstretched and has a modulus of 10000 N/m. Assuming that the coefficient of friction is 0.25, what will be the speed V of block A after dropping 20 cm. k=10000 N/m mc= 40 kg A=0.25 20 cm mB= 40 ka לדלק RB= 20 cm mA= 100 kg
2 Your answer is partially correct. Try again. In the figure, a slab of mass m, = 40 kg rests on a frictionless floor, and a block of mass m, = 9 kg rests on top of the slab. Between block and slab, the coefficient of static friction is 0.60, and the coefficient of kinetic friction is 0.40. A horizontal force F of magnitude 102 N begins to pull directly on the block, as shown. In unit-vector notation, what are the resulting accelerations of (a) the block and (b) the slab? u = 0- (a) Number T-7.4 -7.4 Units m/s^2 (b) Number i+ Units m/s^2 -0.88 Click if you would like to Show Work for this question: Open Show Work SHOW HINT LINK TO TEXT LINK TO SAMPLE PROBLEM LINK TO SAMPLE PROBLEM VIDEO MINI-LECTURE 10:50 PM search ENG 4/4/2021 ond 111Pgup) pri sc DOUSE insert dele home break 13) 23 bac 3 5. 4 R.
A block of mass 50 kg is attached to an extension spring whose spring constant k = 10 N/m. The block originally at rest is pulled by a force P = 100 N as shown in the figure below. The coefficient of kinetic friction along the floor, u = 0.4. Draw the Free Body Diagram and the Kinetic Diagram and calculate the acceleration of the block when the extension of the spring s = 0.5 m. P = 100 N Spring 30
According to the figure where a mass M = z/100 kg on the frictionless floor is being pushed by horizontal m force F. A mass m = 3.00 kg is placed on top of M F M and the coefficient of static and kinetic friction between the surfaces are 0.500 and 0.300, respectively. Find the maximum value of F (in Newton) which allows mass m to move with mass M without slipping. (Use g = 9.80 m/s2)
3. Two blocks are connected by a massless string horizontally. The left block is pulled by a 100N force 30° above horizontal as shown in the figure. Assume the coefficient of kinetic friction between the blocks and the supporting surface is 0.15. (a) Show all the forces acting on each block by drawing its free body diagram. Determine (b) the tension T of the string connecting the blocks and (c) the acceleration a of the blocks. F = 100N 30° 100N T 200N Pk=0.15
3. A box of mass m=15 kg at the packaging section of a factory comes to the top of a ramp (0=37°) with speed vo and slides down where it is picked up for shipment. In order to avoid damage to the box a spring is used with force constant k=100N/m and the maximum force Fmax=100N. The box slides a distance of l=4 m down the incline before it hits the spring is 0.75. as shown. The coefficient of kinetic friction between the box and entire ramp a) Find the work done by the gravity , normal force and friction force on the box until it hits the spring. b) Find the maximum speed of the box at the top of the ramp if the box is to be picked up spring is maximum compression. when the in www
An ideal cord (no mass and no elongation under load) is wrapped around a disc of radius r (r=50 cm, J=0,4 kgm²). The free end of the cord is connected to the mass of m=3kg. The disc is pin jointed and no friction is arisen at the pin. The cord does not slide on the disc and the system is at rest initially. When the system is released the mass, due to the gravity, starts a to move with acceleration a. Find the acceleration of the mass, and the change in the linear momentum of the mass as well as in the angular momentum of the disc during 3 seconds. g=9.81 m/s²
3. Two blocks, mı = 9 kg and mɔ = 15 kg, are connected by a light string that passes over a frictionless pulley as shown in the figure. The first block lies on a horizontal surface and is connected to a spring with 45 N/m force constant. The system is released from rest when the spring is at equilibrium (unstretched). If the kinetic friction between mị and the surface is 0.20, calculate: (a) the distance h which the hanging block falls before coming to rest. (b) the work done by the spring on mị (c) the work done by the string on m || k