öalg äbäi The closed-loop system transferfunction of a control system isgiven by the following figure, forunit step input what is the* ?output2(s – 2)R(s) (s +2)(s + 1)c(s)|%Da- -1+e-2t – e-tb- -1 – e-2t+ e-tc- -1 + 4e-2t – 3e-td- -1 – 4e-2t + 3e¬tad

Answered: Image /qna-images/answer/22e068e4-df62-4c6e-878b-9e85acae2368.jpg

Answered: The closed-loop system transfer…

Engineering

Mechanical Engineering

The closed-loop system transfer function of a control system is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. A mechanical system is shown in the following figure, where external force u₁ is the input and displacement y₂ is the output. The force acting on m₂ has a linear relationship with u₁ as u₂-Au₁. • List system equations and do Laplace transform to the system equations; • Draw block diagram of the control system. (Please construct the block diagram from system equations directly, do not derive or combine the equations. Do not need to reduce it) YI Y b₁ m₁ 11 112 + m₂ www
9 Reduce the following block-diagram into one block. (Describe the control system with one transfer function and write it.) * W2 W1 W3
The ratio of output to input of a system is known as Transfer function. Select one: O True O False Coloct the cinmple cuctom fcom the fellouuing
200 OOOD O Subject Date: Q1/Find the domain P the function 2. Y3DIn(2x+X-6-6)
03/A heating system shown in figure 1; the mathematical model of this system is written as: Ct, = q - 41 C†2 = 91 - 92 Here 91 = T-T2 91 = R1 T-To R2 Derive the transfer funetion for the system assuming q, is the input and q; is the output, and then draw the block diagram which describes the system graphically. Hint: C, C2, R1. Rz are constants. T. Outside Air inside the oven 92 R2 Figure I T
1) Consider the system below: Vehicle Controller Steering dynamics Desired Actual bearing angle bearing angle 50 1 K s2 + 10s + 50 s(s + 5) Figure 1: Simplified Block Diagram of a Self-Guiding Vehicle's Bearing Angle Control. • Find a K value that the system has minimum rise time and minimum overshoot. Let us call this proportional gain as Kopt Show each step while finding Kopt- Show the necessary graphical solutions. Simulate the system response with 3 different K values. (Kopt and two other K values close to Kopt) Show the system response (actual bearing angle) in a single graph for different K values. • Comment on the results.
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
The Gilles & Retzbach model of a distillation column, the system model includes the dynamics of a boiler, is driven by the inputs of steam flow and the flow rate of the vapour side stream, and the measurements are the temperature changes at two different locations along the column. The state space model is given by: x = 0 00 -30.3 0.00012 -6.02 0 0 0 -3.77 00 0 -2.80 0 0 Is the system?: a. unstable b. C. not unstable x+ 6.15 0 0 0 0 3.04 0 0.052 not asymptotically stable d. asymptotically stable -1 u y = 0 0 0 0 -7.3 0 0 -25.0 X
10- To enter the transfer functions G(s)= a) G= th(2, [3,2]) b) c) d) G(s) TH (2, [2, 3]) G= tf (2, [3,2]) G(s)= TF(2, [2, 3]) 2 3s+2 c) A marginally stable response d) A marginally unstable response to Matlab command use: 3s+1 11- To enter the transfer function g(s)= $2+35+2 ,can be use a) num=[3, 1]; den= [1, 3, 2]; g-tf (den, num) num=[3, 1]; den=[1, 3, 2]; g=tf (num, den) b) c) num=[3; 1]; den=[1, 3, 2]; g=tf (den, num) d) num=(3, 1); den=(1, 3; 2); g-tf (num, den) 12- What is the output of the code (>>p=[0 1]; q=[ 1 -1 0]; step(p,q) ) a) An unstable response b) A stable response (s+1)
Match the transfer function with correct Bode phase plots. G(s) = 5 $+7 G(s)=s+5 G(s) = s+10 S S G(s) = S+ 10 QUESTION 10 90 deg 00 0 deg -90 deg 180 deg B. D 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg
Q: Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Feed Reactor temperature set point (master) TC Water surge tank i Jacket itemperature i set point (slave) TC LC-LT Reactor Cooling water out Product Cooling water makeup Circulation pump Figure (2)
Q.4- A model for feedback control system employing both angular position and velocity feedback is shown in figure bellow .The equation describing d²0 do di the system is J di² - = • K.[V₁-K₁0. K₂0-Ka ((1) Summing V,(r) Motor 白口食 amplifier Velocity sensor K₂8 Position sensor Where J is the rotary inertia KandK are the position and velocity feedback gains, and K, is the gain between the input voltages to the motor torque produced. Derive expression for the closed loop system undamped natural frequency and damping ratio.