The compound gear train of a three stages reduction gear is use to transmit power from a power source to a drum with 1 meter in diameter, as shown in Figure P4. The power source generates 500 Nm torque at the speed of 500 rpm and can produce acceleration of 10 rad/s. Assume there is no friction in the drum, mass of the cable is negligible and the cable is in-eastic. With this condition, determine the folbwing. i. Anguar vebcity and acceleration of the drum. Power required to overcome the friction torque in the bearing. Power required to accelerate the inertia of the gear system. Load M that the drum can Ift. ii. iv.

The compound gear train of a three stages reduction gear is use to transmit power from a power source to a drum with 1 meter in diameter, as shown in Figure P4. The power source generates 500 Nm torque at the speed of 500 rpm and can produce acceleration of 10 rad/s. Assume there is no friction in the drum, mass of the cable is negligible and the cable is in-eastic. With this condition, determine the folbwing. i. Anguar vebcity and acceleration of the drum. Power required to overcome the friction torque in the bearing. Power required to accelerate the inertia of the gear system. Load M that the drum can Ift. ii. iv.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

TakuLar Me5sod Method Q3:- The Fig. below shows an epicyclic gear train in which the gear Dis held stationary by shaft A and arm B is rotating at 200 rpm ccw. The gears E and F are carried by the arm. The gear G is rigidly attached to shaft C. Find the magnitude and direction of the speed of shaft C. If the gear train is transmitted 7.5 kW what is the torque required to hold shaft A stationary? Given that Z;-40, Z6=30 and Ze=20. B
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
(d) A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown in Figure Q1(d). The friction torque at winch shaft is 15 Nm and at the motor shaft is 10 Nm. At the motor speed of 1500 rpm, the winch complete one rotational cycle in 11 s. (i) Calculate the equivalent moment of inertia of the drive referred to the motor shaft. (ii) Examine the motor torque if the gear and winch has efficiency of 90% and 98%, respectively. (iii) Find total power of the motor. Winch 0.2 m radius Motor Jo = 0.5 kgm? Gear Cable Jg = 0.15 kgm? at the motor speed Load 500 kg Figure Q1(d)
Problem 3.4: The following particulars of a single reduction spur gear are ziven. Gear ratio 10:1, Distance between the centres 660 mm approximately. Pinion transmits 50 kW at 1800 rpm. Involute teeth of standard proportions: ddendum 1 module with pressure angle of 22.5°; Permissible normai ressure between teeth = 175 N per mm of width. Find Standard module if no interference is to occur No of teath on aach whaal
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
a) Engine-Pump mechanism in Figure 3.1 shows few gears meshing with different parameters . Based on the picture shown below. Given: n1 = 500 rpm; N1 = 20; N2 = 70; N3 = 18; N4 = 54 Compute : (i) value of n4 (i) Torque and power changes at Gear 4 n1, N1 n4, N4 Engine Pump n2, N2 n3, N3 Figure 3.1
The following drive system is used to raise a load at constant velocity. The motor rotational speed is 1000 rpm, and the rotational speed of the drum is 200 rpm. The efficiency of the gear box is 0.85. The efficiency of the drum is 0.95%. The moment of inertia of the motor (input shaft) is 0.5 kg.m², and the moment of inertia of the drum (output shaft) is 0.75 kg.m². Calculate: (1) The total (equivalent) moment of inertia of the drive system referred to the motor shaft. (2) The developed mechanical power on the motor Drum, 0.5 m diameter shaft. 1000 Kg Motor Gearbox
For the complex gear train shown, calculate the velocity ratio (VR). @2 = @3 W4 130 rpm N, = 45 N, = 90 N, = 80 %3D N3 = 20
Epicyclic gear box is shown in Figure.2, the gear box has outer gear C with 120 teeth, B has 50, D has 50 and E has 120.1. Calculate the gear box ratio2. Find the output speed and holding torque of the gear box, if the input gear has 1570 ??? clockwise, the input power 28.5 ?? and the efficiency is 85.5%3. You have engaged in open discussion in which you have to evaluate the conditions needed for an epicyclic gear train to become a differential. Using appropriate schematic and hand sketch show how a differential works in this application. Also, explain what needed to convert the gearbox in Figure.3 to Simple epicyclic differential
A motor with a power rating of 1800 Watts is coupled to the input shaft of the pinion (or driver), Gear A as shown in Figure c, the input shaft rotates at 650 revolutions per minute (rpm). Calculate the torque at the input shaft and at the output shaft. Assume no losses and 100% efficiency. Gear A: 22 TeethGear B: 48 TeethGear C: 30 TeethGear D: 70 Teeth
Q4/ A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a riding tractor. A 5-hp single-cylinder engine is used. At most, 60 percent of this power is transmitted to the belt. The driving sheave has a diameter of 6.2 in, the driven, 12.0 in. The belt selected should be as close to a 92-in pitch length as possible. The engine speed is governor-controlled to a maximum of 3100 rev/min. Select a satisfactory belt and assess the factor of safety and the belt life in passes.
For the gear mechanism in the figure: P1 = 4 kW, η1 = 1000 rpm, z1 = 18, z2 = 36, z3 = 54, z4 = 108, z1 is the driving gear. Total efficiency values for each stage; Since η12 = η34 = 0.96; Find the output torque and speed of gear z4.