The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin connected at O, A, B, and C. h The dimensions are OA-240 mm, AB-240 mm, BC-650 mm and theta-20deg. The plane drives at constant velocity on the airport runway. The weight of the plane is 25 kN. D decimal. 101 OA BC B AB o Find the magnitude of the force in the pin A (magnitude). Give your answer in kN with one

The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin connected at O, A, B, and C. h The dimensions are OA-240 mm, AB-240 mm, BC-650 mm and theta-20deg. The plane drives at constant velocity on the airport runway. The weight of the plane is 25 kN. D decimal. 101 OA BC B AB o Find the magnitude of the force in the pin A (magnitude). Give your answer in kN with one

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.91P: What is the ratio L/R for which the uniform wire figure can be balanced in the position shown?

See similar textbooks

Similar questions

Three Wheels. Three rubber wheels are mounted on axles so that they make tight contact with each other and their centers are on a line. The wheel on the far left axle is connected to a motor that rotates it at 35.0 r.p.m.; and drives the wheel in contact with it on its right which, in turn, drives the wheel on its right. The left wheel (Wheel 1) has a diameter of d₁ = 0.22 m, the middle wheel (Wheel 2) has d₂ = 0.32 m, and the far right wheel (Wheel 3) has d3 = 0.48 m. (a) If Wheel 1 rotates clockwise, in which direction does Wheel 3 rotate? (b) What is the angular speed of Wheel 3, and what is the tangential speed on its outer edge? (c) What arrangement of the wheels gives the largest tangential speed on the outer edge of the wheel in the far right position (assuming the wheel in the far left position is driven at 35.0 r.p.m)? (d) What is the largest tangential speed on the outer edge of the wheel in the far right position? (a) (b) Angular speed of Wheel 3: (c) Number Tangential speed…
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Q1/ A shaft rotating at 120 r.p.m is supported in bearing 4 and B, 1.8 m apart, A being at the left – hand end. Two unbalanced rotating masses of 7.5 kg and 10 kg at radii of 75 mm and 50 mm respectively are situated between A and B at distances of 0.6 m and 0.9 m respectively from A. The angle between the radii is 60" when viewed along the shaft. Answer the following questions: 1- The dynamic forces are .. 2- Forces on bearings A and B due to dead weight are 3- Resultant force at A and B are . and .. 4- A rotor supported at A and B carries two masses. The rotor is . (a) dynamically balanced (b) statically balanced (c) both (a)&(b) (d) none. 5- The static balancing is satisfactory for low-speed rotors but with increasing speeds, dynamic balancing becomes necessary. This is because, the and . and (a) unbalanced couples are caused only at higher speeds (b) unbalanced forces are not dangerous at higher speeds (c) effects of unbalances are proportional to the square of the speed (d)…
Q1/ A shaft rotating at 120 r.p.m is supported in bearing A and B, 1.8 m apart, A being at the left- hand end. Two unbalanced rotating masses of 7.5 kg and 10 kg at radii of 75 mm and 50 mm respectively are situated between A and B at distances of 0.6 m and 0.9 m respectively from A. The angle between the radii is 60" when viewed along the shaft. Answer the following questions: 1- The dynamic forces are. 2- Forces on bearings A and B due to dead weight are .. ., and. 3- Resultant force at A and B are .. . and 4- A rotor supported at A and B carries two masses. The rotor is (a) dynamically balanced (b) statically balanced (c) both (a)&(b) (d) none. and ..
Araure below Cawies turo makses The Sheft Shown m The at Cand D m nhe Same axial Plane but diametrieally Opposite to Raeh orher. 3kg is 2m Im Calculate he dymamic hocauls On Nhe bearings whon The Shaft otates al IHASPM. kalh Mass is 3ka at 6omm radins,
Qi:- Four masses AIB.CanddD revolve at equal vadil and are equallyspaced alony a shaf. The mass8 is7Ky mnd the radiiofcand D make angles of 90 and 240' respectively with theradius of8 Find the magnitude of the masses A Cand D and the angular position of Asothat the System.may be Completely balanced. (Ans 5 gi6kg, 467 kg; 205 from mass B inanticlockwise
The iillustration depicts a prototype design for the High-G Rover. It is made up of an arm that is attached to a shaft that is pinned to a disk. The aarm has a retractable shaft that extends and contracts to cause the disk to rotate. To make the computation easier, let us assumee that the arm does nott rotate A. If the arm's total length is L = 640mm, the distance from the centre of the disk to the shaft pin is r = 112mm, and the arm rotates clockwise at a constant angular velocity of 250.273 rpm. 1.) Would an increase in angular velocity increase point C's linear velocity relative to point A? If so, why or why not? a.) What is the linear velocity of point C with respect to point A if the angular position of the pin (between AB and BC) is 0.578 radians? b.) What is the distance between points A and C if the angular position of the pin (between AB and BC) is 0.578 radians? c.) What is the linear velocity of point C with respect to point A if the angular velocity is increased by 34.34…
The pinion (gear 2 on shaft a) rotates at 695 rev/min clockwise and transmits 1497 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 3 mm, and gears 4 and 5 have a module of 2 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. Co 18T- 327 X 18T 5 -48T
This airplane nose wheel assembly is raised by applying a torque M, as shown. The arm AD and the wheel have a combined weight of 100lbs, and the center of gravity is at G, as shown. Determine the torque required to maintain the assembly at the configuration shown in the following figure (D is directly below B and ?= 15°). 16" B M 20" 32" 20"
2. If the mass of body A and B are equal but k = 2ks, then a. IA = 2IB b. C. IA = d. IA = IA = ¹2IB 4IB ¹14IB
The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 2 mm, and gears 4 and 5 have a module of 3 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. The figure is not to scale. Please give your answer in units of newtons. geard 615 verimin m₂ = M₁ = 2mm 187 327 187 487 MG M₁ = ₂ = 3mm 0=20° I solved it and дог 692.60 Х សុំ But fr is not correct
The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 2 mm, and gears 4 and 5 have a module of 3 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. The figure is not to scale. 187 327 487