The number of bits required for a binary code to represent 712 different possibilities is Select one: O a. 12 bits O b. 10 bits O c. 16 bits O d. 13 bits O e. 14 bits
Q: (b) Figure 2 shows a rectangular magnetic core with relative permeability of the core is 4000. The…
A:
Q: 2. The equivalent_ represents the electrical fields distribution between the two wires of the…
A: The objective is to determine the correct option for the transmission line parameter.
Q: Find the voltage gain Vo/V₁ of the Op-Amp
A: Operational amplifier- An integrated circuit which amplifies weak electric signals into a strong…
Q: 16. The resistance of a parallel circuit consisting of two branches is 12 ohms. If t resistance of…
A: Given, Two branch parallel circuit with, Req=12 ΩR1=18 ΩR2=?
Q: Please determine(with a complete solution): a.) R_E b.) Z_i, Z_o, A_V, A_VS, A_i
A:
Q: 18. A current of 16 amperes divides between two branches in parallel of resistances 8 ohms and 12…
A:
Q: Fuse and circuit breakers are the common household circuit. TRUE OR FALSE
A: Answer: TRUE Because Nowadays in every where we use these fuses and circuit breaker to protect our…
Q: 12. The normalized impedance zL=0.2-j0.2 lies on O the open circuit location O None of them O the…
A: The location of Point in the Smith chart can be found by comparing the given normalized impedance…
Q: An analog-to-digital 16-bit binary input. The input analog voltage range is 0 to 21 V. What is the…
A: Analog to Digital Converter: The Analogue to Digital Converter, or ADC, is a data converter that…
Q: A 750 kW, 3300V, 50 Hz, wound-rotor three-phase induction motor with a star-connected stator winding…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: A 2MVA, 2.3kV 3 Y-connected alternator operates at rated kVA at a power factor of 80%. The DC…
A:
Q: By using thevenins theorem for the circuit shown in Figure below, to find the current in the 3 ohm…
A:
Q: If you have a system with a quantizer of 8V & 4 bits resolution, show the following: 1. howmany…
A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…
Q: 2. What are the norton's current and norton's resistance across points a and b? 592 3/0° A 8Ω -j2Ω…
A: The above circuit can be solved by using KCL and KVL. The solution is given below.
Q: 9ohms Pin 4Ω 8 ohms 120 V 40 30 microfarads E2. In the circuit shown above. the battery has been…
A:
Q: a. Find the function f(t) define by the square waveform shown below. f(t) +HD -2π 2π 3 f b. Find the…
A: For the given square waveform the function f(t) is calculated as shown in below steps. And also for…
Q: Refer to Figure 2, determine the voltage with respect to ground at each point, A, B, C, and D. D₁ R…
A: The circuit diagram is, Assuming the diode is forward bias then diode is replaced by a 0.7 V…
Q: Solve the power triangle at Z6 using the following network law below.
A:
Q: If w = 500 rad/s and I = 2.5 angle 40, find vs(t) ww 10 Ω 1,(1) + 25/-30° V • 25 Ω Μ | 20 mH
A:
Q: 16. The resistance of a parallel circuit consisting of two branches is 12 ohms. If the resistance of…
A:
Q: Problem 33: Find the phase relationship between the following two waveforms: υ = 25 sin(wt +80°) = 4…
A:
Q: Find I in the circuit shown in the figure below using superposition.
A:
Q: Consider the following signal: 5T ㅠ x(n) = 3n+² sin(- -n June) 6 1.1 Determine the z-transform X(z)…
A:
Q: A circuit have following components and values: 6 of a bipolar transistor ranges from 12 to 75 Load…
A: For a bipolar transistor,β=12-75Rc=1.5 ΩRB=0.7 ΩVCC=40 VVB=6 VVCEsat=1.2 VVBEsat=1.6 V
Q: Three important parts of an electric motor are marked A, B and C in the diagram shown below. Choose…
A: In this question electric motor are marked A, B and C in the diagram . We write the name of parts…
Q: Consider the system described by the following diff. eq.: ÿ + 18y + 5y + 12y = 150u Where u is the…
A: In this question we will find transfer function and pole , zero with given differential…
Q: Find ? and ??? ?? if ???=??? in the circuit shown below
A:
Q: Determine Ib, Ic, Ie, Vc, Vb
A: The required parameters can be calculated by using the DC analysis of the amplifier circuit.
Q: 4. The propagation constant consists of two terms. the first term is the attenuation constant, and…
A: We need to select correct option for lossless transmission line
Q: Quiz: Financial Aid Quiz /courses/1406281/quizzes/2268496/take Tube Gmail Combinational logic…
A: There are basically two types of digital circuits that are combinational circuits and sequential…
Q: Suppose the spatial multiparticle wavefunction for 5 identical fermions Y(T1, T2, T3, T4, T5) is…
A: Given,For a single particle,The wavefunction in the state is given by,ψir→jHere,i ∈a, b, c, d, eandj…
Q: . Determine the values of i3, V4, is, and vs in the circuit shown below. + Di Μ 12Ω 18 Ω Mob DA + C…
A: This question belongs to circuit theory . It is based on the concept of current division law and…
Q: Solve the collector-base voltage of an emitter stabilized bias circuit with Vcc=18V, RB-720k ohms,…
A: Assumption Vbe=0.7V This question is related to biasing circuit of bjt
Q: 12. The normalized impedance zL=0.2-j0.2 lies on O the open circuit location O None of them O the…
A: The location of the given Point can be found on the Smith chart by comparing the given normalized…
Q: 2. Find Vo using superposition -j4Ω = 8 Ω Μ +1 10/0° V +1 -j2 Ω 4) 4/0° A j5 Ω m 6Ω 3/0°
A:
Q: bad, and find the maximum power to the load. E is in rms E = 120 V 20° +₁ R₁ www 3 Ω XL moo 4 Ω HE…
A:
Q: Q2: A distributor (d.c ring distributor) of ABCDA is fed from point A with 250 v and has a…
A:
Q: Three resistors of 50 ohms, 100 ohms,
A: Resistance in parallel- 1/Req=1/R1+1/R2+1/R3+........... Resistance in series-…
Q: 2. Find the voltage across a 5µH inductor if i equals A) 30te-t nA B) 4e-5t sin 100t mA
A: We need to find out voltage for given current
Q: If the load of wye connected transformer are: IA = 10 cis(-30ᴼ) IB = 12 cis (215ᴼ) IC = 15 cis…
A:
Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…
A:
Q: The motion of a particle is defined by the relation x=6r*-21³-121² +3t+3, where x and t are…
A:
Q: express in 4 decimals if need be! Four resistors, R1 = 100 ohms, R2 = 250 ohms, R3 = 350 ohms,…
A:
Q: and i₂. Find the Red at terminals a-b in the circuit shown. Also determine i, i₁, 12 a 2 www 6 2 40…
A: This question belongs to circuit theory . It is based on the concept of equivalent resistance ,…
Q: O 50 15. Why should design our circuits to operate below the SRF of electrical elements? to increase…
A: SRF stands for Self Resonant Frequency. This is such frequency above which elements of the circuits…
Q: A 3-phase Wye-Delta Connected source to load system has the following particulars: Load impedance…
A: The concept used here is that the line voltage and phase voltage for delta connected load is always…
Q: Make a circuit of the inverter, AND gate, and OR gate to produce the following output: a. (x + y)'x…
A:
Q: Given the circuit shown below, determine the current in each branch by: a. Nodal Method b.…
A: For the given circuit, we need to determine the current in each branch using (i) Nodal method, and…
Q: For R1=172, R2=177, R3-214, R4-450, R5-435, R6-455, V1=3 V & 11=4 A in the shown circuit, using the…
A:
Q: The potential divider circuit shown in Figure 1 consists of two resistors: R1 and R2. Vin R1 R2 Vo
A: 4. a. Given circuit is shown below. i) Apply KVL in the loop Vin=IR1+R2I=VinR1+R2 The Vo is…
Step by step
Solved in 2 steps
- Q3) A - Convert the Excess-3 to binary number : ( 110001011100.10001010)ex-3 B- convert each Gray code to binary: 1-( 011010001001)G 2-(59)DHow to build this circuit? (on Digital or Logisim) Binary-coded decimal is an alternative method of representing integers using binary. In it, each base-10 digit is represented by four bits, thus each nibble takes one of 10 values (0000 through 1001). Therefore, using BCD, 42 (decimal) is represented as 0100 0010 (binary) and 196 (decimal) is represented as 0001 1001 0110 (binary). Create a circuit in Logisim that accepts as input a pair of two-digit integers represented as BCD and outputs their sum in BCD. Any and all Digital components are fair game. You can assume that all inputs will be valid BCD-encoded numbers.Q1. Show the implementation of 4 bit binary to gray code (shown in below table) converter using either EPROM or PLA. In Gray code only one bit changes at a time. Binary Gray code Decimal equivalent 0000 0000 1 0001 0001 0010 0011 3 0011 0010 4 0100 0110 5 0101 0111 6. 0110 0101 7 0111 0100 8. 1000 1100 1001 1101 10 1010 1111 11 1011 1110 12 1100 1010 13 1101 1011 14 1110 1001 15 1111 1000
- Using excess-15 notation, what is the decimal equivalent of this binary number 1011001110000000. A) 0.123423 B) -0.123423 C) 0.234375 D) -0.234375 E) 0.65342 F) -0.65342 G) 0.37520 H) -0.37520 I) None among the given choicesplease show work included 4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?Q4: For each of the following set of binary numbers, determine the logic states at each point in the logic symbol of 7485 4-bit comparator. a) P3 P2 P1 PO=1100 Q3 Q2 Q1 Q0=1010 b) P3 P2 P1 P0=1001 Q3 Q2 Q1 Q0=1101
- 1) What is the biggest binary number (decimal value) you can write with 6 bits? What is the biggest binary number (decimal value and in terms of n) you can write with n bits? If you want to represent the decimal numbers from 0-16, what is the minimum number of bits you will need? Convert the decimal number 238 to binary number. (ZERO point if not showing steps/calculation!)Assuming even parity, find the parity bit for each of the following data units. a. 1001010 b. 0001101 c. 1000000 d. 111011120. Suppose we have just found yet another representation for floating point numbers. Using this representation, a li2-bit floating point number has 1 bit for the sign of the number, 4 bits for the exponent and 7 bits for the mantissa, which is normalized as in the Simple Model so that the first digit to the right of the radix points must be a 1. Numbers in the exponent are in signed 2's complement representation. No bias is used and there are no implied bits. Show the representation for the smallest positive number this machine can represent using the following format (simply fill in the squares provided). What decimal number does this equate to? : SIGN EXPONENT MANTISSA
- The BCD code can be used to code decimal digits that’s range from [… - …] with ……. Digits (or bits). [0 – 10], 5 [0 – 8], 3 [0 – 9], 4 [0 – 8], 2(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG