The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70066350 Pa and angle of twist of 2.5° for the whole shaft. Use 6 = 83000000000 Pafor the shaft, x = 2.25 m, and y = 1.63 m. Round off the final answer to two decimal places. T 100 mm 70 mm 70 mm y

The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70066350 Pa and angle of twist of 2.5° for the whole shaft. Use 6 = 83000000000 Pafor the shaft, x = 2.25 m, and y = 1.63 m. Round off the final answer to two decimal places. T 100 mm 70 mm 70 mm y

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
NEED ANSWER ASAP The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress in the solid shaft (in Pa) using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70098347 Pa and angle of twist of 2.5ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.13 m, and y = 1.79 m.
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress in the solid shaft (in Pa) using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70041051 Pa and angle of twist of 2.3ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.47 m, and y = 1.62 m. Round off the final answer to two decimal places.
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
The electric motor exerts a torque of 800 N- m on the steel shaft ABCD when it is rotating at a constant speed. The angle of twist between A and D is limited to 1.50 degree. Use maximum shear = 60 MPa and modulus of rigidity = 77 GPa. Solve its torque for each shaft AB and BC. And determine the diameter of the Shaft based on strength. 300 N.m 500 N.m 0.4 m 0.6 m 0.3 m
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
Two solid steel shafts of different diameters are joined together at point C. The diameter of the smaller shaft is 0.5 inch, while the diameter of the larger shaft is 1 inch. If the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb is applied at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi. 8 in 5 in 12 in
: The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: ri = 20mm, ro = 25 mm 2. Center tube: ri = 26 mm, ro = 30 mm 3. Outer tube: ri = 32mm, ro = 38mm
A shaft is made of an aluminum alloy having allowable shear stress of tallow = 100 MPa. If the diameter of the shaft is 100 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T if a 75-mm-diameter hole were bored through the shaft? Sketchthe shear-stress distribution along a radial line in each case.
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 59 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 84 MPa. If a torque of Tc=29400 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = d₂ = i (2) B A mm mm
a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the shear stress in the shaft is limited to 50 mpa. determine the inside outside diameter of the shaft if the ratio of inside to outside diameter of the shaft is 0.4