Include a picture and assumptions about problem 5. A large block of steel is placed inside of a furnace set at 1980°C. If it is assumedthat the surface temperature of the steel instantly takes on the temperature of thefurnace and remains constant, what is the time required for the steel to reach1000°C at a depth of 10 cm? Given: Ksteel = 63.9W/m k, Csteel = 434 J/kg k,Psteel = 7832 kg/m³, Osteel = 18.8 x 10-6 m²/s(State all assumptions and Show All Work)

Given data as per question A large block of steel is placed inside of a furnace of…

Answered: the surface temperature of the steel…

the surface temperature of the steel instantly takes on ace and remains constant, what is the time required fo 0°C at a depth of 10 cm? Given: Ksteel = 63.9W/m k, (

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 : A 2 kW resistance heater wire with thermal conductivity of k = 20 W/m °C, a diameter of D = 5 mm, and a length of L3D0.7 m is used to boil water. If the outer surface temperature of the resistance wire is Ts = 110°C, determine the temperature at the center of the wire. Ans : 121.4 °C
Q2 A 2 kW resistance heater wire with thermal conductivity of k = 20 W/m °C, a diameter of D = 5 mm, and a length of L= 0.7 m is used to boil water. If the outer surface temperature of the resistance wire is Ts= 110°C, determine the temperature at the center of the wire. Q3: Consider a 20-cm-thick large concrete plane wall (k = 0.77 W/m °C) subjected to convection on both sides with T1 = 27°C and h₁ = 5 W/m² °C on the inside, and T2 = 8°C and h₂ = 12 W/m² °C on the outside. Assuming constant thermal conductivity with no heat generation and negligible radiation, (a) express the differential equations and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the temperatures at the inner and outer surfaces of the wall. Ans: (a) Ans: 121.4 °C dT (L) -k dx -=h₂ [T(L)-T₂] (b) T(x) = 20-45.44x Q4: A double pane window consists of 3 mm thick…
A 2m^2 wall of 1010steel is 8 mm thick. If the outside of the wall is100 °C, andyou measure aheat flux of 80 kW/m2coming off the wall, what is the temperature of the insideof thewall?
Q3/A sphere of 30 mm diameter has its surface maintained at 80°C while being immersed in still water at 20°C. Determine the power required to maintain the temperature.
P3. After a particularly cold night, Alice leaves a tub of water outside. You may consider the ground and air to have temperatures of Te = -10°C and Th = 10°C respectively. How thick is the layer of ice that forms at the bottom of the tub of water, after the tub has been left outside for a long time? The tub of water initially has a layer of water of thickness ho 10 cm. You may assume that the ground and air remain at a constant temperature throughout, and that the side lengths of the tub a, b » ho, i.e. the heat conduction is one- dimensional. Density of ice and water are pice = 920 kg/m³ and pw = 1000 kg/m³. Ice and water have thermal conductivities of kice = 2.22 W K-1 m' -1 and kw 0.556 W K-1 m' -1.
A chromel–constantan thermocouple measuring the temperature of a fluid is connected by mistake with copper–constantan extension leads (such that the two constantan wires are connected together and the copper extension lead wire is connected to the chromel thermocouple wire). If the fluid temperature was actually 250 C and the junction between the thermocouple and extension leads was at 90 C, what e.m.f. would be measured at the open ends of the extension leads if the reference junction is maintained at 0 C? What fluid temperature would be deduced from this (assuming that the connection error was not known)?
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
A steel rod, which is free to move, has a length of 200 mm and a diameter of 20 mm at a temperature of 15oC. If the rod is heated uniformly to 115oC, determine the length and diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10-6 m/m/C. Is there a stress on the rod at 115oC?
The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal conductivity is 60 W/m-C. The voltage and current flowing into the heater are 220V and 5A, respectively. Find the temperature at the top portion of the pan. Sketch diagram and show pertinent solutions. Box your final answer and express numerical values in 2 decimal places
a metal bar is made up of 3.0 cm of aluminum and 5.0 cm of steel. the free end of the aluminum bar is placed in contact with steam at 100 degree Celsius. at the other side, the free end of the steel bar maintained at 0 degree Celsius by placing it in contact with the ice. find the temperature at the point that connect the aluminum and the steal (junction)
Saved Help Save & Exit A 2-kW resistance heater wire with thermal conductivity of k= 70 W/m-K, a diameter of D= 4 mm, and a length of L = 0.9 m is used to boil water. If the outer surface temperature of the resistance wire is Ts= 230°C, determine the temperature at the center of the wire. (Round your answer to a single decimal place.) 230 C -D→ es Resistance heater The temperature at the center of the wire is °C 18°C Clear ^ 4 ENG
A 2-kW resistance heater wire with thermal conductivity k = 15 W/m - °C, di- ameter D = 0.4 cm, and length L = 50 cm is used to boil water by immersing Water it in water (Fig. 2-19). Assuming the variation of the thermal conductivity of the wire with temperature to be negligible, obtain the differential equation that de- scribes the variation of the temperature in the wire during steady operation. Resistance heater