The tension member is fastened togother using two bolts, one on each side of the member as shown.Each bolt has a diameter of 0 3 in The allowable shear stress for the bolts is Tall 12 ksi and the allowable average normal stress is oallow- 19 ksiPart ADetermine the maximum load P that can be applied to the memberExpress your answer to three significant figures and include appropriate units.PasValueUnits

Answered: Image /qna-images/answer/4b89116c-b6f1-4998-a1b8-1beb612447a7.jpg

The tension member is fastened togother using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0 3 in The allowable shear stress for the bolts is Talk 12 ksi and the allowable average normal stress is alfow- 19 ksi Part A Determine the maximum load P that can be applied to the member Express your answer to three significant figures and include appropriate units. Pass Value Units

The tension member is fastened togother using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0 3 in The allowable shear stress for the bolts is Talk 12 ksi and the allowable average normal stress is alfow- 19 ksi Part A Determine the maximum load P that can be applied to the member Express your answer to three significant figures and include appropriate units. Pass Value Units

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.4P

See similar textbooks

Similar questions

PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch. Also determine the tensile stress and torsional stress. Indicate on the Mohr circle the principal stresses in the bolt and determine the factor of safety FS.
ll zain IQ 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 1 4 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/ find the bearing stress between bolts and plate
A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The bracket is subject to an eccentric load of 150 kN. Use LRFD. Use A36 steel. Questions a) Determine the critical force on the most stressed bolt. b) Determine the nominal shear stress of the most stressed bolt.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will support a 110kN and the ultimateshearing stress for the steel used is 360MPaand that a factor of safety of 3.35 is desired,determine the increase in the bolt diameterrequired if an additional 100kN load is addedto the existing 110kN.
A L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answers
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.