Tumble flow has been found to accelerate .9 the combustion process and improve engine performance and it can be defines :as A rotational air motion around an axis perpendicular to the crankcase axis A rotational air motion around an axis parallel to the cylinder axis A rotational air motion around an axis perpendicular to the cylinder axis None of the above

Tumble flow has been found to accelerate .9 the combustion process and improve engine performance and it can be defines :as A rotational air motion around an axis perpendicular to the crankcase axis A rotational air motion around an axis parallel to the cylinder axis A rotational air motion around an axis perpendicular to the cylinder axis None of the above

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter4: Automotive Systems

Section: Chapter Questions

Problem 20RQ: What two major engine components work together to change the reciprocating motion of the pistons...

See similar textbooks

Similar questions

Discuss briefly as points the importance of Cetane Number on the combustion process and engine performance for SI Engine
When performing a combustion efficiency test, digital flue gas will measure what four parameters?____________, and________.
19:07 * IZVA KOREK TELECOMIKOREK Asiacell МО The number 8 is pointed to the oil sump. O oil pump. air inlet manifold. water jackets. O exhaust manifold. cylinder head cover. O cylinder block. cylinder head. O
Task 8 - Induction Systems In order for combustion to take place an induction system is required to feed fuel and air into the cylinder of an engine. To improve efficiency and performance spark ignition (SI) engines are now adopting compression ignition (CI) engine technology by injecting fuel directly into the cylinder just before the point of ignition however these engines still require an air induction system. Carburettors: before fuel injection technology had been fully developed carburettors (carbs) were used to create a fuel/air ratio at different engine speeds and loads. A cold start facility was also fitted albeit manually operated. The demand for more performance has meant the fixed choke carb' was no longer suitable. More complex carbs' were developed (twin choke) as well as variable choke (constant depression) carbs which used engine vacuum (during throttle opening) to vary the size of choke according to operating requirements.
Combustion Engine Question is image
Discuss the basic operating principle of Internal combustion engines (ICE) we are currently using (provide drawing if necessary)
a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is the meaning of RON and MON. Define the calculation method of RON. b-) Methane is an alcohol that can be used as an alternative fuel in internal combustion engine. Give two reasons why methanol is a good alternate fuel for automobiles and explain in detail. Than, give two reasons why it is not a good alternate fuel and explain in detail.
B// An engine having a bore of 120 mm, stroke of 160 mm and compression ratio is 10. It used a fuel mixture of 30% C,H, (butane) and 70% C,H, (propane). The dry products of combustion is CO₂-15%, CO-1.5%, 0,-2.5% and the rest is N₂. Calculate: 1- the air/fuel ratio, 2-the mass of the residual gases left in the cylinder at the end of the exhaust stroke if the pressure and temperature are 1.5 bar and 680 K.
It represents the net power output of the engine at the crankshaft. * Your answer If the fuelair ratio is proper and ignition timing is correct, the combustion process should be completed just after center at the beginning of the power stroke. * our answer The ignition time varies from 20 to 35 degrees before the top dead center to ensure complete combustion when the piston is slightly past the top quiet center position. TRUE OR FALSE? * Your answer
Describe the operation of different types of lubrication methods used in a petrol engine (80 - 100 Words) a. Boundary lubrication b. Hydrodynamic lubrication c. Force Feed lubrication d. Mist Feed (Boundary) Į A▾ B I W LEM III
How combustion pressure is sealed by the piston rings and still sufficient lubrication maintained for reciprocation of piston in cylinder?
Discuss briefly as points the importance of Octane Number on the combustion process and engine performance for SI Engine