--A double-threaded power screw with square threads pushes against a load of 3,822 N at a speed of 15 mm/s. The screw has a major diameter of 20 mm and a pitch of 6 mm. Thefrictional coefficient of the threads is 0.25, and collar friction is negligible.What is the rotational speed of the screw in units of revolutions per minute?Type your answer...2 points

Here, p is pitch, is major diameter of screw.

Answered: What is the rotational speed of the…

Engineering

Mechanical Engineering

What is the rotational speed of the screw in units of revolutions per minute?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A square-threaded power screw has a mean diameter, dm = 1.75 in and a pitch, p = 0.875 in. The coefficient of thread friction is 0.10 and the collar friction is negligible. What horsepower is required to raise a weight of 3000 lbf at a rate of 20 ft/min?
A single-threaded power screw with square threads pushes against a load of 3,736 N at a speed of 42 mm/s. The screw has a mean thread diameter of 12 mm and a pitch of 3 mm. The frictional coefficient of the threads is 0.34, and collar friction is negligible. How much torque must be applied to drive the screw against the applied load in units of newton meters? Type your answer... -D
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mm
A single-threaded power screw of square form is to raise a load of 90KN at the rate of 360mm/min. Other data are as follows: Nominal Diameter of screw = 36mm Pitch = 6mm Coefficient of thread friction = 0.1 Coefficient of collar friction = 0.08 Friction radius at collar= 30mm Determine the power input to the screw in kilowatts.
Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
Consider a screw used in translation along with a 22 mm. inside diameter and 38 mm. outside diameter collar. The screw has a mean; diameter of 18 mm. and has a single trapezoidal metric thread cut with a pitch of 4 mm. Determine the torque required to raise a load of 500 kg, if both the collar and the threads have a coefficient of friction of 0.3.
Problem 1 The SERO CHIENS C is recreating rolling large stone columns by animal power and pivot points cut into the center of each of the column. The friction in each pivot point plus the rolling resistance creates a resisting couple of 300 ft*lb (like a rusty bearing). The yoke angle B = 10°. a) Determine how many horses (i.e. horsepower https://en.wikipedia.org/wiki/Horsepower) they need to move a 4600-lb column that is 10 ft long and 2 ft in diameter up a 0 = 5° slope from rest to 3 miles per hour after 15 feet of travel. b) Determine how many horses they need to maintain a constant speed of 3 mph up the slope. Round your answers up to the nearest integer. A fraction of horse doesn't pull very well. Assume the column rolls without slipping.
A single-threaded power screw with square threads pushes against a load of 3,276 N at a speed of 14 mm/s. The screw has a mean thread diameter of 18 mm and a pitch of 2 mm. The frictional coefficient of the threads is 0.33, and collar friction is negligible. How much torque must be applied to drive the screw against the applied load in units of newton meters? A double frictiona
A A10¹ 4 bartleby.com/questions-an Q SEARCH ASK 愚CHAT VX MATH SOLV A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mm Expert Solution Step 1 Given: W = 70 KN d = 33.375 mm p=6 mm 11-tand-013 9:26 AM Q मं
Please solve ellaborately and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You. A pulley 190 mm. in diameter transmits 22 kW at 350 rpm. The arc of contact between the belt and pulley is 115.7° having a center distance of 410 mm. Determine (a) diameter of the driven pulley for open belt drive,(b) speed of the driven pulley, and (c) belt length for an open belt connection. (a) Diameter of Driven Pulley Answer and unit for part 1 (b) Speed of the Driven Pulley Answer and unit for part 2 (c) Belt Length
1. A machine vice, as shown in the figure has single start, square threads with 22 mm nominal diameter and 5 mm pitch. The diameter of the collar is 55 mm. the coefficients of friction for thread and collar are 0.15 and 0.17 respectively. The machinist can comfortably exert a force of 125 N on the handle at a mean radius of 150 mm. Assuming uniform wear for the collar, a) Calculate the clamping force developed between the jaws, b) Calculate the overall efficiency of the clamp. Fixed jaw Moving jaw Frame Screw 150 mm Handle
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.