winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b.

winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: A 200/100 V, 50 Hz transformer is to be excited at 40 Hz from the 100 V side. For the exciting…

A: Excitation current = E/X

Q: ) Which of the following statement is true about Current Transformer? a. The current in the…

A: Current transformer is used to measure high current.

Q: A single phase transformer has turns ratio of 4. The resistance and reactance of the primary winding…

Q: transformer having primary voltage of 230V and the number of turns in the primary and secondary are…

Q: A 50 Hz 1-phase transformer has a turn-ratio of 6. The resistances are 0.90 ohm and 0.03 ohm and…

A: Given data : Resistance and reactance on the HV side R1=0.90Ω, X1=0.03Ω Resistance and reactance on…

Q: How does change in frequency affect the operation of a given transformer? with a decrease in…

A: Transformer:

Q: During short-circuit test, iron losses are negligible because the voltage applied on primary side is…

A: let us arrive at the right answers in each case by analyzing the given statement as shown below.

Q: sentences: 8) The primary mmf is not equal and same direction to the secondary mmf in an ideal…

A: The question is about characteristics of Ideal transformer.

Q: 1. Explain the working principle of transformer with neat sketch and what are the losses occurred in…

A: Working principle of transformer Transformer is a electrical passive device it amplifies voltage at…

Q: DC 200 V is applied to the primary of a transformer with a conversion ratio of 1/5. From secondary…

A: The winding functions as a short circuit through the source terminals of DC when a DC voltage is…

Q: What will happen if the primary of a transformer is connected to D.C supply? Answer:

Q: Identify, which component of no load current supplies hysteresis loss, in a practical transformer?…

A: In the question choose the correct option? which component of no load current supplies hysteresis…

Q: 2-An ideal transformer consists of a primary winding (100 turn) and a secondary winding (1000 turn).…

A: Given here an ideal transformer primary winding turns and secondary winding turns and secondary…

Q: What is the use of current transformer? Draw it's block diagram.

Q: When an ohmic load is connected to the secondary of a 220/110 Volt transformer (primary voltage is…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: In a transformer the no-load voltage is 250 V. Calculate the percentage of voltage regulation if the…

A: According to the question we have to find the value of voltage regulation and the terminal voltage…

Q: The eddy-current loss in a 6.9 kV, 50 Hz transformer is 220 W. What will be the eddy-current loss of…

Q: Which of the following quantities remain constant in a step-up transformer? a. Current b.…

A: We need to select the quality which remains constant in step up transformer.

Q: 11) Which phenomenon is used in transformer to change the values of alternating voltages and…

A: Given that Which phenomenon is used in transformer to change the values of alternating voltages and…

Q: Belonging to a phase measured from a 220/48 V phase transformer, no-load (no load) operation and…

Q: current supplies hysteresis loss, in a practical transformer? a. None of these b. IM c. IC d. I0

Q: B- the eddy current losses of 400V, 50 Hz transformer is 1600W and the total iron losses i 2500W.…

A: Transformer Transformer is a static electrical device which transfers power from one circuit to…

Q: 2. The resistance of a transformer windings is 0.25 ohms at 25 degrees Celsius. When operating at…

A: Given that α0=4.27×10-3 /°Ct1=25°Ct2=75°CR1=0.25 ohmR2=? It is known that…

Q: Core losses of a single phase 400/240 V, 20 kVA, 50 Hz transformer is 700 W. Maximum efficiency of…

A: Given, Core losses of a single phase 400/240 V, 20 kVA, 50 Hz transformer is 700 W. (Pi=0.7 kW)…

Q: B)-Bescribe various losses in transformer. Explain how each loss varies with load current, supply…

A: Type of transformer Single phase transformer Three phase transformer Star Star connection Star…

Q: The transformation ratio for the below transformer is 5:1. Assume 240Vrms is applied to the…

Q: single-phase transformer with a rating of 50kva has an iron loss of 400 W and a full load copper…

A: The solution is given below

Q: FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its…

A: (a) In the question following data is given Np=720 Ns=144 Vs=42 volt Vp can be found by following…

Q: The resistances of potential transformer winding is minimized by using a thick conductors and small…

A: Answer:a thick conductors and small length of turns

Q: How many primary volts must be applied to a transformer with a turns ratio of 0.1 to obtain a…

A: Solution Given data, turns ratio =0.1…

Q: For the ideal transformer derive the relation between the following terms: a) N₁ arid N₂ b) Land L2…

A: (a) Given the primary turn ratio is N1 and N2.

Q: voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 2V. If the maximum flux…

A: We know direct formula of per winding voltage. From that formula we will find out cross section…

Q: What is difference in magnetization characteristic of iron core used to design a metering and…

Q: a)The voltage per winding of 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum…

A: The solution can be achieved as follows.

Q: The efficiency of a transformer will be maximum when ........................? (A) copper losses =…

Q: The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the core…

A: eddy current loss is given as Pe= k f2Bm2 t2

Q: During Short Circuit test at full-load current the power input to a transformer contains: Select…

A: consider the given circuit;

Q: A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: When secondary is fully loaded, transformer regulation is less than 1 percent. It shows that it is a…

A: This problem is related to the transformer If the secondary is fully loaded, transformer regulation…

Q: FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its…

A: Given, the secondary Voltage V2= 42 V Rated output power = 2750 W The load Resistances RL1 = 1.66…

Q: When 120 V, 60 Hz is applied to the primary winding of a transformer, the core loss is 240 W. When…

Q: Q3 (a) Indicate how the performance of a transformer will change given the following changes to the…

A: The transformer has a primary and a secondary side. It converts electrical power to electrical power…

Q: ist FOUR (4) types of losses and its definition that occur in a real model of a transformer.

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: How many primary volts must be applied to a transformer with a turns ratio of 0.5 to obtain a…

A: step 1turns ratio K=0.5Secondary voltage V2=15VPrimary voltage…

Q: 10. Draw a neat diagram of a practical transformer on load, with winding resistance and leakage…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: What does a transformer require on its primary

A: Requirements at primary of transformer : There are mainly two side of transformer one is primary…

Q: A transformer with normal voltage impressed has a flux density of 1.4 Tesla at rated frequency and a…

A: At given condition we need to find Eddy current loss and hysteresis loos of the given transformer.

Q: Example 2-2. The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be…

Question

Answer only please

The resistance of a transformer winding is 0.25 ohm at 25^oC. When operating at full load, the temperature of the winding is 75^oC. The temperature coefficient of resistance for copper at 0^oC is 0.00427 per ^oC. What is the winding resistance at full load?

0.512 ohm

0.315 ohm

0.298 ohm

0.271 ohm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
DC 200 V is applied to the primary of a transformer with a conversion ratio of 1/5. From secondaryExplain the reason for this by writing the voltage value to be made?
A 200V/100V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be the same, the applied voltage should be ?
Note: explain your solution A certain transformer has a ratio of 8 is to 1. the primary winding resistance is 0.00283 ohm per turn and has 1155 more turns than the secondary winding. if the copper losses in the primary is 20% less than in the secondary, find the resistance of the secondary winding.
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
The equivalent resistance of the primary of a transformer having K = 6 and R1 = 0.2 ohm when referred to secondary becomes.......ohm. Group of answer choices 0.004 7.2 0.72 0.0055
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?
In a load test on transformer the no load voltage is 240V. The terminal voltage drop is 225V on resistive load condition. The primary voltage of transformer is 350V. The primary and secondary currents are 0.45A and 0.671A. What is the efficiency of the transformer? O a. 68% O b. 95.85% O c. 64% O d. 43.19%
b) A certain winding made up of copper has a resistance of 100 Q at room temperature. If resistance temperature coefficient of copper at 0 C° is 0.00428/C°, calculate the winding resistance if temperature is increased to 45 C°. Assume room temperature as 25 C°.
How do i calculate secondary current in transformer analysis