Concept explainers
A pump draws propane at
Want to see the full answer?
Check out a sample textbook solutionChapter 13 Solutions
Applied Fluid Mechanics (7th Edition)
Additional Engineering Textbook Solutions
Vector Mechanics For Engineers
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Machine Tool Practices (10th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Introduction To Finite Element Analysis And Design
- A large container filled with water and uncovered for use in fighting fires in an ethylene production plant. Water from this tank is pumped into the nozzle when needed use. This fire suppression system is designed to be able to transmit 1890 L/min of water at a pressure of 15 bar (relative pressure). If we ignore the difference in height between the water level in the tank and pump, there is no change in diameter of pipe and nozzle, pump efficiency is 70%. Ask how much work (hp) is required to the pump to achieve the desired pressure and flow would like?arrow_forwardA centrifugal pump discharging 900 gpm and operates at 1800 rpm against a head of 120 feet has a power output of 30 hp. If the pump is to operate at 1200 rpm assuming efficiency remains constant. Determine the new discharge in gpm, the head and power.arrow_forwardA fuel pump is delivering 18 gallons per minute of oil with a specific gravity of 0.80. The total head is 75 meters. If the power input to the pump is 1.1 hp, what is the eficiency of the pump?arrow_forward
- A small centrifugal pump is used to deliver 0.005 m3/s of water to level 2 as shown in Fig. 2. Neglecting the losses, determine the required power input to the pump if its efficiency is equal to 70%.arrow_forwardA fuel pump is delivering 18 gallons per minute of oil with a specific gravity of 0.80, the total head is 75 m. If the power input to the pump is 1.1 hp, what is the efficiency of the pump?arrow_forwardA submersible pump deliver 350 gpm of water to a height of 5ft from the ground. the pump was installed 120 ft. below the ground level and a draw down of 8 ft. during the operation, if water level is 25 ft. above the pump, determine the pump powerarrow_forward
- 2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.arrow_forwardDetermine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47marrow_forwardwhile the pressure remains constant at 85 psig, the volume of air changes from 12ft^3 to 20ft^3. Find the amount of work done on or by the closed system?arrow_forward
- A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. Include the diagram in your solution. A.2.56 B.12.74 m C.-2.72 m D.-4.67 marrow_forwardA pump delivers water, density =1000kg/m3, at a volume flow rate of 0.004256 m3/sec. If the head developed by the pump is 4.01 m, determine the fluid power in Watts. Take g=9.81 m/s2. State the answer to two decimal places.arrow_forwardFor a pumper truck pumping water to a fire, the back pressure is the additional pressure on the pump caused by the height of the nozzle. (Another way of thinking of back pressure is as the minimum pressure the pumper must produce in order to make water flow out the end of the nozzle.) Consider a pumper at street level pumping water through a hose to firefighters on the top of the ninth floor of a building. If each floor is 16 feet high, what is the head of water at the mouth of the nozzle?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY