Fundamentals of Geotechnical Engineering (MindTap Course List)
5th Edition
ISBN: 9781305635180
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 18.14P
A steel pile (H-section; HP 360 × 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone:
Unconfined compression strength = qu(lab) = 78.7 MN/m2
Angle of friction = 36°
Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 30 m long concrete pile is 305 mm times 350 mm in cross section and is fully embedded in a sand deposit. Using Broms' method, calculate the allowable lateral load Q_g (take FS = 2) at the ground level. Assume the pile is flexible and restrained. Let the soil unit weight, gamma = 16 kN/m^3, the soil friction angle, Phi' = 30^degree; and the yield stress of the pile material, F_y = 21 MPa,
A group pile in clay is shown in the figure below. Determine the maximum vertical load Qg
be applied if the allowable consolidation settlement of the pile group is set to be 0.17 m. Use the
2:1 stress distribution method to estimate the average effective stress in the clay layer.
can
Qg
3 m
Sand
Groundwater
y = 15.72 kN/m3
table
Sand
3 m
Ysat =
18.55 kN/m3
2.75 m
X 2.75 m
Group
plan
Normally consolidated clay
Ysat = 19.18 kN/m³
15 m
18 m
eo = 1
C.
= 0,8
Normally consolidated clay
Ysat = 19 kN/m3
eo = 0.25, C. =1
5 m
Rock
11.22 A concrete pile measuring 0.406 m X 0.406 m in cross section is 18.3 m long. It is
fully embedded in a layer of sand. The following is an approximation of the me-
chanical cone penetration resistance (q.) and the friction ratio (F) for the sand
layer. Estimate the allowable bearing capacity of the pile. Use FS = 4.
Depth below ground surface (m)
9. (kN/m²)
F, (%)
0-6.1
2803
2.3
6.1-13.7
3747
2.7
13.7-19.8
8055
2.8
Chapter 18 Solutions
Fundamentals of Geotechnical Engineering (MindTap Course List)
Ch. 18 - State whether the following are true or false. a....Ch. 18 - A 1500 kN load was applied on two 20 m long and...Ch. 18 - A 500 mm diameter and 20 m long concrete pile is...Ch. 18 - A 400-mm diameter and 15 m long concrete pile is...Ch. 18 - A 400 mm 400 mm square precast concrete pile of...Ch. 18 - Prob. 18.6PCh. 18 - Prob. 18.7PCh. 18 - Prob. 18.8PCh. 18 - Determine the maximum load that can be allowed on...Ch. 18 - Prob. 18.10P
Ch. 18 - Redo Problem 18.10 using the method for...Ch. 18 - Determine the maximum load that can be allowed on...Ch. 18 - Prob. 18.13PCh. 18 - A steel pile (H-section; HP 360 1.491; see Table...Ch. 18 - A concrete pile is 18 m long and has a cross...Ch. 18 - Prob. 18.16PCh. 18 - Prob. 18.17PCh. 18 - Prob. 18.18PCh. 18 - Prob. 18.19PCh. 18 - Figure 18.26a shows a pile. Let L = 20 m, D = 450...Ch. 18 - Refer to Figure 18.26b. Let L = 15.24 m, fill =...Ch. 18 - Prob. 18.22PCh. 18 - Figure 18.39 shows a 3 5 pile group consisting of...Ch. 18 - The section of a 4 4 group pile in a layered...Ch. 18 - Prob. 18.25PCh. 18 - Prob. 18.26CTP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A concrete pile 20 m long having a cross section of 0.46 m × 0.46 m is fully embedded in a saturated clay layer. For the clay, given: Yat = 18 kN/m², = 0, and Cu = 80 kN/m?. Determine the allowable load that the pile can carry (FS = 3). Use %3D the A method to estimate the skin resistance.arrow_forwardA braced sheet pile to be used in an open cut in clay is shown in the figure. Struts are spaced longitudinally at 2.5 m center to center spacing. Unit weight of clay is 20 kN/cu.m and an unconfined compressive strength of 100 kN/m2. Determine the section modulus of wale at B if the allowable bending stress is 0.6 Fy where Fy = 248 MPaarrow_forwardQUESTION 3 A concrete pile is driven into top two layers of subsoil strata made of 10m and 5m thick saturated clays respectively. The pile's diameter is 500 mm throughout the pile. Determine the allowable bearing capacity of the pile. The subsoil properties are shown. (Answer 454 kN). Clay layer 1: Saturated unit weight of clay = 18kN/m3 Average undrained shear strength = 100kPa, o = 0 %3D Adhesion factor = 0.48 Clay layer 2: Saturated unit weight of clay = 19kN/m3 Average undrained shear strength = 120kPa, q = 0 Adhesion factor = 0.42, Nc = 9.arrow_forward
- A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate load carrying capacity of the pile. -0.8- Clay Cu = 60 kN/m² Y = 18 kN/m³ %3D 4m G.W.T Sand 6m $ = 30° Y = 20 kN/m³ Clay Cu = 100 kN/m² Y = 20 kN/m³ 5marrow_forwardA square concrete pile of 10 m length is driven into a deep layer of uniform homogeneous clay. The average unconfined compressive strength of the clay, determined through laboratory tests on undisturbed samples extracted from the clay layer, is 100 kPa. If the ultimate compressive load capacity of the driven pile is 632 kN, the required width of the pile is mm. (in integer) (Bearing capacity factor Nc = 9; adhesion factor a = 0.7)arrow_forwardA 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).arrow_forward
- Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin frictionarrow_forwardA concrete pile 20 m long with a cross section of 400 mm x 400 mm is fully embedded in a saturated clay layer. The clay has the following properties: γsat = 18.5 kN/m3, ϕ= 0 and cu = 70 kPa. Assume that the water table rises to the tip of the pile. Determine the allowable load that the pile can carry (FS=3). Use the α and λ method to estimate the skin resistance.arrow_forwardPILE FOUNDATIONS • Example: 35/1 A machine foundation is supported by four prestressed concrete plies driven to bedrock. The length of each pile is 24 m, and they are 0.3 mx 0.3 m in cross section. The weight of the machine and the foundation is 1360 kN. Given: unit weight of concrete = 24 kN/m¹ and the modulus of elasticity of the concrete used for the piles = 24.5 × 106 kPa. Determine the natural frequency of the pile foundation system.arrow_forward
- 5. A concrete pile is 20 m long has a cross section of 0.46 m × 0.46 m. The pile is embedded in a sand having y=17 kN/m³ and Ø= 38°. The allowable working load is 1200 kN. If 700 kN are contributed by frictional resistance and 500 kN are from the point load, determine the elastic settlement of the pile. Given: Ep = 21×106 kN/m², Es = 30×10³ kN/m², µs=0.38 and = 0.57.arrow_forwardA 400 mm x 400 mm square precast concrete pile of 15 m length is driven into a sand where γ = 18.0 kN/m3 and Φ' = 33°. Assume δ' = 0.7 and K=1.4Ko determine the load-carrying capacity of the pile with a FS=3. Using Meyerhof's method, Qp=Apq'Nq*≤Apql for computing the point load-carrying capacity Qp, Equations, L'≈15D and f=Kσ'otanδ' for computing the load-carrying capacity of the pile shaft Qs.arrow_forwardA concrete pile 50 ft long having a cross section of 15 in. x 15 in. is fully embedded in a saturated clay layer for which γsat = 121 lb/ft3, Φ = 0, and cu = 1600 lb/ft2. Determine the allowable load that the pile can carry. (Let FS = 3.) Use the a method Eq. (9.59) and Table 9.10 to estimate the skin friction and Vesic’s method for point load estimation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Types of Foundation in building construction in detail - Civil Engineering Videos; Author: Civil Engineers;https://www.youtube.com/watch?v=7sl4KuM4UIE;License: Standard YouTube License, CC-BY
Types of Foundation || Foundation Engineering; Author: Civil Engineering;https://www.youtube.com/watch?v=AFLuAKGhanw;License: Standard Youtube License