Industrial Motor Control
7th Edition
ISBN: 9781133691808
Author: Stephen Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 52, Problem 4RQ
What conditions of input must exist if an AND gate is to produce a high output?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
need in s domain
The equation underneath is do to with resonance, however resonance occurs when the input frequency is equal to the natural frequency what does this equation mean?
Explain part c please, why do you have flux symbol there? Can you show work for limit to get laplace transform or work to get to laplace tranform
Chapter 52 Solutions
Industrial Motor Control
Ch. 52 - In a relay circuit, what function is served by the...Ch. 52 - Prob. 2RQCh. 52 - What conditions of input must exist if an OR gate...Ch. 52 - What conditions of input must exist if an AND gate...Ch. 52 - When connecting TTL logic, why are inputs pulled...Ch. 52 - Prob. 6RQCh. 52 - Referring to Figure 52–12, what function does the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Name two effects of negative feedback.arrow_forwardwhen i input 0 for x=0 and y=0, it does c2 does not equal zero. is there a reason why it is zero?arrow_forwardThe ratio of output to input of a system is known as Transfer function. Select one: O True O False Coloct the cinmple cuctom fcom the fellouuingarrow_forward
- The system will have a direct connection between the output and input.arrow_forwardB-4-10. Consider the liquid-level control system shown in We assume that the velocity of the power piston (valve) K₁.x where K₁ is a positive constant. We also assume that the change in the inflow rate q, is negatively proportional to the change in the valve opening y, or Figure 4-52. The inlet valve is controlled by a hydraulic is proportional to pilot-valve displacement .x. or integral controller. Assume that the steady-state inflow rate is and steady-state outflow rate is also, the steady-state head is , steady-state pilot valve displacement is X = 0, and steady-state valve position is Y. We assume that the set point R corresponds to the steady-state head H. The set point is fixed. Assume also that the disturbance inflow rate 94, which is a small quantity, is applied to the water tank at = 0. This disturbance causes the head to change from to H+h. This change results in a change in the outflow rate by qo. Through the hydraulic controller, the change in head causes a change in the…arrow_forwardProblem 1. The following equation is given. W(p) = K (K₁ + TIP Find the differential equation and define the type of the control low. Draw the control structure.arrow_forward
- Find the differential equation and define the type of the control low. Draw the control structure. Problem 2 A pressure is measured with a sensor with range-1 to 10 bars. If it generates a current with range between 4 and 20 mA, please calculate the pressure if 10 mA is measured at the PLC Input;arrow_forwardMeans that data concerning the effects of the computers commands are fed back to the computer as an input signal.arrow_forwardQ2. The application glven as In figure A &B can be realized by using an ultra-sonic sensor. Also explain how triangulation method can be used for the same. Using sultable diagrams, explain the process of operation elaborately. Hll semor Oututpu tan s be courted tita) Figure A Soo: SENSOR OUT Figure Barrow_forward
- Hello, i am asked to create my own statics problem, here are the specifications. Thank you very much!!!!arrow_forwardFind the moment about A & B where AB = 8m, BC = CD 6m & all forces makes 40° to horizontal axis. 7kN 8 kN 10KN 15kl 6kN 5kN B. 3kN 4kNarrow_forwardYou are tasked to enhance the performance of an analog plant using a digital controller PID. The controller is in connected in series with the plant in a closed-loop configuration. The pulse transfer K(z+a) function is given as GzohGp(s) =- Use sampling time Ts=0.6 second, K=8, a=0.78, b=-0.602 (0+z)(q+z) and c=-0.705. Do the following: i. Obtain the design point in z-coordinates to achieve the requirement of having a system settling time of 3 second, and damping ratio of zeta (z=0.705).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License