Fox and McDonald's Introduction to Fluid Mechanics
Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
bartleby

Videos

Textbook Question
Book Icon
Chapter 7, Problem 42P

An airplane wing of 3 m chord length moves through still air at 15°C and 101.3 kPa at a speed of 320 km/h. A 1:20 scale model of this wing is placed in a wind tunnel, and dynamic similarity between model and prototype is desired. (a) What velocity is necessary in a tunnel where the air has the same pressure and temperature as that in flight? (b) What velocity is necessary in a variable-density wind tunnel where absolute pressure is 1400 kPa and temperature is 15°C? (c) At what speed must the model move through water (15°C) for dynamic similarity?

Blurred answer
Students have asked these similar questions
The drag force on a submarine, which is moving on the surface, is to be determined by a test on a model which is scaled down to one-twentieth of the prototype. The test is to be carried in a towing tank, where the model submarine is moved along a channel of liquid. The density and the kinematic viscosity of the seawater are 1010 kg/m³ and 1.3x10-6 m 2/s, respectively. The speed of the prototype is 2.6 m/s. Assume that F = f(V, L. g. p.), using pi-theorem and similarity principle to: a) Determine the speed at which the model should be moved in the towing tank. b) Determine the kinematic viscosity of the liquid that should be used in the towing tank.
An engineer is to design a human powered submarine for a design competition. The overall length of the prototype submarine is 2.24 m and its engineer designers hope that it can travel fully submerged through water at 0.560 m/s. The water is freshwater (a lake) at 7-15°C (p=999.1 kg/m3 and u= 1.138 ×103 kg/m-st. The design team builds a one-eighth scale model to test in their university's wind tunnel. The air in the wind tunnel is at 25°C (p= 1.180 kg/m3 and u = 1.849 ×10-5 kg/m-s) and at one standard atmosphere pressure. At what air speed do they need to run the wind tunnel in order to achieve similarity?
An underwater device which is 2m long is to be moved at 4 m/sec. If a geometrically similar model 40 cm long is tested in a variable pressure wind tunnel at a speed of 60 m/sec with the following information, Poir at Standard atmospheric pressure = 1.18kg/m³ Pwater = 998kg/m3 Hair = 1.80 x 10-5 Pa-s at local atmospheric pressure and Hwater = 1 × 10-3 Pa-s then the pressure of the air in the model used times local atmospheric pressure is

Chapter 7 Solutions

Fox and McDonald's Introduction to Fluid Mechanics

Ch. 7 - Assume that the velocity acquired by a body...Ch. 7 - Derive by dimensional analysis an expression for...Ch. 7 - The speed of shallow water waves in the ocean...Ch. 7 - The speed, V, of a free-surface wave in shallow...Ch. 7 - The boundary-layer thickness, , on a smooth flat...Ch. 7 - The speed, V, of a free-surface gravity wave in...Ch. 7 - Derive an expression for the velocity of very...Ch. 7 - Derive an expression for the axial thrust exerted...Ch. 7 - Derive an expression for drag force on a smooth...Ch. 7 - The energy released during an explosion, E, is a...Ch. 7 - Measurements of the liquid height upstream from an...Ch. 7 - The load-carrying capacity, W, of a journal...Ch. 7 - Derive an expression for the drag force on a...Ch. 7 - A circular disk of diameter d and of negligible...Ch. 7 - Two cylinders are concentric, the outer one fixed...Ch. 7 - The time, t, for oil to drain out of a viscosity...Ch. 7 - You are asked to find a set of dimensionless...Ch. 7 - A continuous belt moving vertically through a bath...Ch. 7 - Derive an expression for the frictional torque...Ch. 7 - Tests on the established flow of six different...Ch. 7 - The power, P, required to drive a fan is believed...Ch. 7 - The sketch shows an air jet discharging...Ch. 7 - The diameter, d, of bubbles produced by a...Ch. 7 - Choked-flow nozzles are often used to meter the...Ch. 7 - A large tank of liquid under pressure is drained...Ch. 7 - Spin plays an important role in the flight...Ch. 7 - The power loss, P, in a journal bearing depends on...Ch. 7 - The thrust of a marine propeller is to be measured...Ch. 7 - The rate dT/dt at which the temperature T at the...Ch. 7 - When a valve is closed suddenly in a pipe with...Ch. 7 - An airship is to operate at 20 m/s in air at...Ch. 7 - An airplane wing of 3 m chord length moves through...Ch. 7 - A flat plate 1.5 m long and 0.3 m wide is towed at...Ch. 7 - This 1:12 pump model using water at 15C simulates...Ch. 7 - An ocean-going vessel is to be powered by a...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - A 1:3 scale model of a torpedo is tested in a wind...Ch. 7 - A flow rate of 0:18 m3/s of water at 20C...Ch. 7 - A force of 9 N is required to tow a 1:50 ship...Ch. 7 - An airplane wing, with chord length of 1.5 m and...Ch. 7 - A water pump with impeller diameter of 24 in. is...Ch. 7 - A model hydrofoil is to be tested at 1:20 scale....Ch. 7 - A ship 120 m long moves through freshwater at 15C...Ch. 7 - A 1:30 scale model of a cavitating overflow...Ch. 7 - In some speed ranges, vortices are shed from the...Ch. 7 - A 1:8 scale model of a tractor-trailer rig is...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - When a sphere of 0.25 mm diameter and specific...Ch. 7 - The flow about a 150 mm artillery projectile which...Ch. 7 - Your favorite professor likes mountain climbing,...Ch. 7 - A 1:50-scale model of a submarine is to be tested...Ch. 7 - Consider water flow around a circular cylinder, of...Ch. 7 - A 1:10 scale model of a tractor-trailer rig is...Ch. 7 - The power, P, required to drive a fan is assumed...Ch. 7 - Over a certain range of air speeds, V, the lift,...Ch. 7 - The pressure rise, p, of a liquid flowing steadily...Ch. 7 - An axial-flow pump is required to deliver 0.75...Ch. 7 - A model propeller 1 m in diameter is tested in a...Ch. 7 - Consider Problem 7.38. Experience shows that for...Ch. 7 - Closed-circuit wind tunnels can produce higher...Ch. 7 - A 1:16 model of a bus is tested in a wind tunnel...Ch. 7 - The propagation speed of small-amplitude surface...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
Express each force in Cartesian vector form and then determine the resultant force FR. Find the magnitude and c...

INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)

What parts are included in the vehicle chassis?

Automotive Technology: Principles, Diagnosis, and Service (5th Edition)

In what ways is a thermit weld similar to the production of a casting?

DeGarmo's Materials and Processes in Manufacturing

Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License