A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).
Trending nowThis is a popular solution!
Learn your wayIncludes step-by-step video
Chapter 1 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Additional Engineering Textbook Solutions
Foundation Design: Principles and Practices (3rd Edition)
Problem Solving with C++ (9th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Artificial Intelligence: A Modern Approach
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Database Concepts (7th Edition)
- A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.arrow_forwardThe frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.arrow_forwardA cylindrical rod with a diameter of 15.24 mm and a gauge length of 400 mm is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.45 mm when the applied load is 31000 N, which of the four metals or alloys listed below are possible candi- dates? Justify your choice(3). TABLE P1.12 Material E (GPa) Yield Strength (MPa) Tensile Strength (MPa) Steel alloy 1 Steel alloy 2 Titanium alloy Сopper 180 860 502 200 400 250 110 900 730 117 220 70arrow_forward
- To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.arrow_forwardA cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.4 mm when the applied load is 30 KN. Which of the four metals or alloys listed below are possible candidates. Justify the answer with calculations Material modulus of elasticity(gpa) yield strength(mpa) tensile strength(mpa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Copper 110 210 275 Steel alloy 207 450 550arrow_forwardA metal rod with 0.5 inch diameter is subjected to 2000 lb tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is 10,000,000 psi, Poisson’s ratio is 0.33 and the yield strength is 21,000 psi.arrow_forward
- A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).arrow_forwardA steel bar of 500 mm length is under tensile stress of 100 N/mm?. If the modulus of elasticity is 2 x 10" N/m?, then the total elongation of the bar will bearrow_forwardA tensile stress is applied along the long axis of a cylindrical aluminum rodwith a diameter of 10 mm. If the deformation is entirely elastic, determine themagnitude of the load required to produce a 2.5 * 10-3mm change in diameter. Assume a modulus of elasticity of 70 GPa and a Poisson’s ratio of 0.33.arrow_forward
- A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the tótal deformation of the bar if it has a modulus of elasticity E= 28.5 x 10^6 psi. %3D O 0.1378 inches O 0.1338 inches O 0.1352 inches O 0.1364 inches O 0.1423 inchesarrow_forwardA metal rod with 0.5 in. diameter is subjected to 2000 lb tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is 10,000,000 psi, Poisson’s ratio is 0.33, and the yield strength is 21,000 psi.arrow_forwardA force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and having a yield strength of 400 MPa and a tensile strength of 480 MPa,Determinea. whether the bar will plastically deform; andb. whether the bar will experience neckingarrow_forward
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage LearningSteel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage LearningConstruction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning