Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
thumb_up100%
Chapter 11, Problem 11.2P
A rectangular ASTM A36 steel bar 2 in. by 6 in. in cross section is subjected to an axial tensile load of 300,000 lb. The proportional limit of the steel is 34,000 psi. Compute the change in the transverse 6-in. dimension.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule03:09
Students have asked these similar questions
a short square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000 lbs. calculate the shear stress and the tensile stress acting on the plane which is mormal and is inclined 50 degrees to the longitudinalm axis of the bar. what is the factor of safet for the bar?
A 1.25 inch diameter hole is drilled on the centerline of a steel bar 3.5 inches wide by 3/8 inches thick. Calculate the maximum load that can be applied to the bar without exceeding the maximum stress in the bar of 22,000 psi.
Can you help me with this problem?
Problem Solving: Show your Solution
1. A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tall vertical pillar. The pillar’s cross-sectional area is 0.20 m20.20 m2 and it is made of granite with a mass density of 2700kg/m3.2700kg/m3. Find the compressive stress at the cross-section located 3.0 m below the top of the pillar and the value of the compressive strain of the top 3.0-m segment of the pillar.
2. A 2.0-m-long steel rod has a cross-sectional area of 0.30cm2.0.30cm2. The rod is a part of avertical support that holds a heavy 550-kg platform that hangs attached to the rod’s lower end.Ignoring the weight of the rod, what is the tensile stress in the rod and the elongation of the rodunder the stress?
3. In a hydraulic press, a 250-liter volume of oil is subjected to a 2300-psi pressure increase. If the compressibility of oil is 2.0×10−5/atm,2.0×10−5/atm, find the bulk strain and the absolute decrease in the volume of oil when the press is operating.…
Chapter 11 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 11 - Prob. 11.1PCh. 11 - A rectangular ASTM A36 steel bar 2 in. by 6 in. in...Ch. 11 - Calculate Poisson’s ratio for a cast iron that has...Ch. 11 - Modulus of elasticity, modulus of rigidity, and...Ch. 11 - Compute all the dimensional changes for the steel...Ch. 11 - A surveyor’s steel tape is exactly 100ft long...Ch. 11 - An aluminum wire is stretched between two rigid...Ch. 11 - Prob. 11.8PCh. 11 - A concrete roadway pavement is placed in 60ftlong...Ch. 11 - Prob. 11.10P
Ch. 11 - A 4in. -by- 8in . short wood post is reinforced on...Ch. 11 - A short post. 150mm by 150mm , of Douglas fir, is...Ch. 11 - The cables of a power line are copper-coated steel...Ch. 11 - Prob. 11.14PCh. 11 - For the short column shown, assuming that lateral...Ch. 11 - A 1.0 -in.-diameter hole is drilled on the...Ch. 11 - Prob. 11.17PCh. 11 - A long, flat steel bar 4 in. wide and 38 thick is...Ch. 11 - A long, flat steel bar 5 in. wide and 38 thick has...Ch. 11 - 11.20 An aluminum specimen of circular cross...Ch. 11 - Prob. 11.21PCh. 11 - Prob. 11.22PCh. 11 - 11.23 A concrete cylinder, -in, in diameter, was...Ch. 11 - Prob. 11.24PCh. 11 - For the element of Problem 11.24: a. Locate the...Ch. 11 - Prob. 11.26CPCh. 11 - Prob. 11.27CPCh. 11 - Prob. 11.28CPCh. 11 - Prob. 11.29CPCh. 11 - A 50 -mm-diameter ASTM A36 steel rod is subjected...Ch. 11 - A 4 -ft-long square ASTM A36 steel bar, 2 in. by 2...Ch. 11 - A concrete test cylinder is 150 mm in diameter and...Ch. 11 - A 14 -in.-long steel rod, 112 in diameter, was...Ch. 11 - Determine the change in the diameter of an ASTM...Ch. 11 - 11.35 The steel bar shown in Figure 11.3 (see...Ch. 11 - Compute the change in the thickness of the ASTM...Ch. 11 - The steel rails of a railroad track are laid in...Ch. 11 - A rolled brass rod and a steel rod are secured to...Ch. 11 - 11.39 A -m-long steel member is set snugly between...Ch. 11 - 11.40 The distance between two fixed points on a...Ch. 11 - A steel truss is loaded as shown. The...Ch. 11 - 11.42 For the truss of Problem 5.25, the members...Ch. 11 - A surveyor’s steel tape has a cross-sectional area...Ch. 11 - A 1 -in.-diameter ASTM A36 steel tie rod, 30 ft...Ch. 11 - 11.45 A copper wire is held taut between two...Ch. 11 - 11.46 A horizontal steel member is anchored at...Ch. 11 - 11.47 Three vertical steel wires are loaded as...Ch. 11 - 11.48 Assume for Problem 11.47 that the same load...Ch. 11 - The rod shown is firmly attached to rigid...Ch. 11 - 11.50 A structural steel bar mm in width and mm...Ch. 11 - A redwood timber member having a 16 -in.-square...Ch. 11 - A steel pipe has an outside diameter of 12 in. and...Ch. 11 - A short 14 -in.-square concrete pier is reinforced...Ch. 11 - An ASTM A36 steel rod, 375.06 mm long and having a...Ch. 11 - An aluminum rod with an area of 1.5in.2 and an...Ch. 11 - A solid brass cylinder with a cross-sectional area...Ch. 11 - Three 14 in.-diameter wires are symmetrically...Ch. 11 - Rework Problem 11.57 with outer wires of aluminum,...Ch. 11 - Three rods support a weight, as shown. The...Ch. 11 - A flat steel bar 4 in. wide and 12 thick must be...Ch. 11 - A 19 -mm-diameter hole is drilled on the...Ch. 11 - A flat bar is 38 thick and has a centrally located...Ch. 11 - A long, flat steel bar 125 mm wide and 10 mm thick...Ch. 11 - 11.64 A short -in.-diameter compression member is...Ch. 11 - Prob. 11.65SPCh. 11 - 11.66 A rectangular block of wood, in. by in. in...Ch. 11 - 11.67 A -mm-diameter rod is subjected to an axial...Ch. 11 - The rectangular plate shown is subjected to a...Ch. 11 - A wood block, subjected to a tensile load, fails...Ch. 11 - Prob. 11.70SPCh. 11 - A shaft in a speed-reduction mechanism is loaded...Ch. 11 - An axially loaded 50 -mm-by- 75 -mm steel bar has...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
28. The force on the inside of a cork in a champagne bottle is 10 pound-force [lbf]. If the cylindrical cork ha...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
The uniform plate has a weight of 500 lb. Determine the tension in each of the supporting cables. Prob. F5-7
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
State if these members are in tension or compression. Probs. 6-39/40
Engineering Mechanics: Statics
11. If a pump moves water at 70 gallons per minute [gal/min or gpm], what is the volumetric flow rate in units ...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
If the transition between the cross sections has a radius r = 4 mm, determine the maximum torque that can be a...
Mechanics of Materials (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.arrow_forwardCalculate the change in dimensions in the bar.F = 12000 N; h= 0.01 m; w= 0.03 m; L = 0.8 m; E = 60 GPa; v = 0.3arrow_forwardA long, flat steel bar 6 in. wide and 3/8 in. thick has a circular hole 2 in. in diameter, centrally located. The allowable tensile stress for the steel is 22,000 psi. Be aware of the existance of stress concentration, calculate the maximum axial tensile load that my be applied to the bar: ____ lb. Calculation your answer to 1 decimal place.arrow_forward
- Q5/ Calculate the maximum stress in a round steel bar, 200 mm diameter and 15 m long. due to its own weight when it is simply supported at its ends. Density of steel, 7.75 mg/ m'.arrow_forwardA 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24marrow_forwardA cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MPa.Calculate the transverse stress in steel.arrow_forward
- A steel rod 8 mm in diameter is under the action of a tensile force (P) of 600 Newton. Calculate the tensile stress (s) acting in the bar. Solve for Mpa (round up to whole number)arrow_forwardCalculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add filearrow_forwardA steel rod having a length of 1 m has a crosssectional area of 100 mm^2 Use E = 200 GPa. If it is subjected to an axial tensile force, compute the stiffness of the rod in kN/mm.arrow_forward
- A steel rod having a length of 1m has a cross-sectional area of 100mm^2. if it is subjected to an axial tensile force, compute the stiffness of the rod. Use E = 200 GPaarrow_forwardA stepped bar is subjected to an axial tensile force of 40000 lb.Compute the increase in stress due to stress concentration in the bar with D =12.00 in., d = 4.00 in., and r = 0.4 inarrow_forwardCalculate the maximum normal strain in the bar in με.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanics of Materials Lecture: Beam Design; Author: UWMC Engineering;https://www.youtube.com/watch?v=-wVs5pvQPm4;License: Standard Youtube License