Problems 11–2 and 11–3 raise the question of the reliability of the bearing pair on the shaft. Since the combined reliabilities R is R1R2, what is the reliability of the two bearings (probability that either or both will not fail) as a result of your decisions in Probs. 11–2 and 11–3? What does this mean in setting reliability goals for each of the bearings of the pair on the shaft?
The reliability of two bearing.
Answer to Problem 4P
The reliability of two bearing is
Setting the reliability goals for each bearing depends on the combined reliability of the bearings.
Explanation of Solution
Write the expression for multiple of rating life for bearing.
Here, multiple of rating life for design is
Write the regression equation for bearing load life.
Here, the bearing load for design is
Write the equation for bearing life.
Here, the rating life in hour is
The below figure shows the relationship between bearing load and dimensionless life in terms of logarithmic values.
Figure-(1)
Write the equation for reliability along a constant load line
Here, the characteristic parameter is
Write the expression for catalog rating in terms of application factor.
Here, catalog rating is
Write the expression for combined reliabilities.
Here, combined reliability is
Conclusion:
For first bearing.
Substitute
Substitute
Thus, the multiple of rating life of bearing is
Substitute
For ball bearing, the value of constant
Substitute
Substitute
Refer table 11-2 “Dimensions and Load Rating of Ball Bearing” to obtain the ball bearing at catalog rating of
Thus, the catalog rating of bearing is
Substitute
Substitute
Substitute
Thus, the reliability of the bearing is
For second bearing:
Substitute
Thus, the multiple of rating life of the bearing is
Substitute
Substitute
For roller bearing, the value of constant
Substitute
Substitute
Refer to table 11-2 “Dimensions and Load Rating of Ball Bearing” to obtain the ball bearing at catalog rating of
Thus, the catalog rating of the bearing is
Substitute
Substitute
Substitute
Thus, the reliability of the bearing is
Substitute
Reliability goal can be achieved by setting the reliability of one bearing and according to it the reliability of other bearing is achieved.
Substitute
Thus, the setting the reliability goals for each bearing depends on the combined reliability.
Want to see more full solutions like this?
Chapter 11 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
- What is the lifetime in hours of a 02-series angular contact ball bearing with a 35 mm bore, and a dynamic load rating of 27.0 kN when when running at 1125 rpm under a sustained radial equivalent load of 11.35 kN? Assume a a reliability level of 90%. Please round your answer to the nearest hour. Type your answer... L 37 6:47 AMarrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of 26 kh at a speed of 455 rev/min. The radial load is 2.5 kN and an application factor of 1.2 is appropriate. The reliability goal is 0.92. Find the multiple of rating life required, xD , and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11–2 and estimate the reliability in use.arrow_forwardThe design of journal bearings usually involves two suitable combinations of variables: variables under control and dependent variables or performance factors. As such, a full journal bearing has a shaft journal diameter of 27 mm with a unilateral tolerance of 20.01 mm. The bushing bore has a diameter of 27.04 mm with a unilateral tolerance of 0.03 mm. The //d ratio is unity. The bushing load is 1.03 kN, and the journal rotates at 1153 rev/min. You are required to analyze the minimum clearance assembly if the average viscosity is 50 mPa.s to find the minimum oil film thickness, the power loss, and the percentage of side flow.arrow_forward
- A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is (2000+N) N and an application factor of 1.2 is appropriate. Find the catalog rating C10 For ball bearings For roller bearings The Weibull parameters are and Use SI units. Take the relations as and Where the subscripts D: desired R: rating f: factorarrow_forwardUse the general shaft layout given and determine critical diameters of the shaft based on infinite fatigue life with a design factor of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the recommended limits in Table 7-2. Assume that the deflections for the pulleys are not likely to be critical. 10 in 500 lbf 75 lbf 8-in dia. Bearing at O 10.0" 500 lb d 75 lb Material 1040 Q and T 18 in Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions in the belt at pulley Bare T₁ and T2, where T₁ is 15% of T2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 10-in dia. 12 in T₂ 8.0⁰ T₁ 18.0" 10.0" I B pulley diameter = 8.0" Sut 113 kpsi T2 T1 pulley diameter = 10.0" Sy 86 kpsi 12.0" Bearing at C Using the DE-Goodman criteria and a design factor of 1.5, calculate the diameter based on the shaft's loadings…arrow_forwardSelect an angular contact ball bearing to carry a radial load of 336lb at a shaft speed of 1800 rpm for 5500 hours. Anapplicationfactorof1.2isappropriate. Use a reliability of 96%.arrow_forward
- Two single-row 02-series angular contact ball bearings with inner ring rotation are to be selected by a student for her Capstone project from Table 11-2 to support a radial load of 3.5 kN and axial load of 1.25 kN. The desired total machine reliability is 95%. The desired life of the bearings is 1 year of continuous operation in a machine operating at 900 rpm with light to moderate impact. Use the "manufacturer 2" Weibull values from Shigley Table 11-6 and equivalent radial load factors from Table 11-1. Fully specify the smallest bore size for these conditions.arrow_forwardThe shaft below is supported by 0.5 in long copper-iron light-duty journal bearings at A and B. Determine the maximum allowable shaft speed (in rpm) consistent with a bearing factor of safety of 1.8. F = 225 lbf Bearing A Bearing B 1.1 in Walow = ? 5.75 in 0.5 in 1.5 in 0.5 inarrow_forwardThe design load on a ball bearing is 413 lbf and an application factor of 1.2 is appro- priate. The speed of the shaft is to be 300 rev/min, the life to be 30 kh with a reliability of 0.99. What is the C10 catalog entry to be sought (or exceeded) when searching for a deep-groove bearing in a manufacturer's catalog on the basis of 106 revolutions for rat- ing life? The Weibull parameters are xo = 0.02, (0 – xo) = 4.439, and b = 1.483. %3Darrow_forward
- ....The rating life at 90% reliability for a ball bearing is 15 x 106 revolutions. If the bearing is subjected to an equivalent radial load of 2000 N, which of the following is its dynamic load rating? Group of answer choices 4506 N 4932 N 1890 N 1665 Narrow_forwardBall bearings are rated by a manufacturer for a life of 106 revolutions. The catalogue rating of a particular bearing is 16 kN. If the design load is 2 kN, the life of the bearing will be Px 106 revolutions, where Pis equal toarrow_forwardA 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr= 8 kN, axial load Fa= 3 kN, design life LD = 10°, ring rotation factor V= 1.2, and reliability RD= 0.95. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the C10 value for this application. The C10 value for this application is kN.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY