Concept explainers
Determine the enthalpy change and the entropy change of oxygen per unit mole as it undergoes a change of state from 220 K and 5 MPa to 300 K and 10 MPa (a) by assuming ideal-gas behavior and (b) by accounting for the deviation from ideal-gas behavior.
(a)
The change in specific enthalpy and entropy of oxygen per unit mole by assuming ideal-gas behavior.
Answer to Problem 73P
The change in specific enthalpy and entropy of oxygen per unit mole by assuming ideal-gas behavior is
Explanation of Solution
At ideal gas state, the enthalpy is the function of temperature only.
Write the formula for difference in molar specific enthalpy of oxygen at ideal gas state.
Here, the molar enthalpy at ideal gas state corresponding to the temperature is
Write the formula for change in molar specific entropy.
Here, the molar specific entropy at reference sate is
Refer Table A-19, “Ideal-gas properties of oxygen,
Obtain the initial properties corresponding to the temperature of
Obtain the final properties corresponding to the temperature of
The universal gas constant
Conclusion:
Substitute
Substitute
Thus, the change in specific enthalpy and entropy of oxygen per unit mole by assuming ideal-gas behavior is
(b)
The change in specific enthalpy and entropy of oxygen per unit mole by accounting for the deviation from ideal-gas behavior.
Answer to Problem 73P
The change in specific enthalpy and entropy of oxygen per unit mole by accounting for the deviation from ideal-gas behavior is
Explanation of Solution
Write formula for enthalpy departure factor
Here, the molar enthalpy at ideal gas state is
Rearrange the Equation (III) to obtain
Refer Equation (IV) express as two states of enthalpy difference (final – initial).
Write formula for entropy departure factor
Here, the molar entropy at ideal gas state is
Rearrange the Equation (VI) to obtain
Refer Equation (VII) express as two states of entropy difference (final – initial).
Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.
The critical temperature and pressure of oxygen gas is as follows.
The reduced pressure
The reduced pressure
At initial:
Refer Figure A-29, “Generalized enthalpy departure chart”.
The enthalpy departure factor
Refer Figure A-30, “Generalized entropy departure chart”.
The entropy departure factor
At final:
Refer Figure A-29, “Generalized enthalpy departure chart”.
The enthalpy departure factor
Refer Figure A-30, “Generalized entropy departure chart”.
The entropy departure factor
Conclusion:
Substitute
Substitute
Thus, the change in specific enthalpy and entropy of oxygen per unit mole by accounting for the deviation from ideal-gas behavior is
Want to see more full solutions like this?
Chapter 12 Solutions
Thermodynamics: An Engineering Approach
- Determine the enthalpy change for 1 kg of nitrogen which is heated from 300 to 1200 K by (a) using the gas tables, (b) integrating Cp(T), and (c) assuming constant specific heat. Use M = 28 kg/kmol. %3Darrow_forwardA mole sample of liquid ammonia at 273 Kelvin is cooled to liquid ammonia at 240 Kelvin. The process is done irreversibly by placing the sample in liquid nitrogen at 77 Kelvin. The heat capacity relationship for ammonia gas is given below. Assuming that the heat of vaporization is 23.4 KiloJoules per mole, answer the questions that follow. What is the entropy change of this process (in Joules per Kelvin)? Express answer in THREE SIGNIFICANT FIGURES. What is the entropy change of the surroundings for this process (in Joules per Kelvin)? Express answer in THREE SIGNIFICANT FIGURES. What is the total entropy change (or the entropy of the universe) for this process (in Joules per Kelvin)? Express answer in THREE SIGNIFICANT FIGURES.arrow_forwardNOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A piston–cylinder device contains 6 kg of H2 and 21 kg of N2 at 160 K and 5 MPa. Heat is now transferred to the device, and the mixture expands at constant pressure until the temperature rises to 200 K. Determine the heat transfer during this process by treating the mixture as a nonideal gas and using Amagat’s law. The universal gas constant is Ru = 8.314 kPa·m3/kmol·K. Use the table containing the molar mass, gas constant, and critical-point properties; the generalized enthalpy departure chart; and the table containing the ideal-gas properties of air.arrow_forward
- Express the Joule coefficient and the Joule – Thomson coefficient as its value for an ideal gas.arrow_forwardOne mole of an ideal monatomic gas, initially at a pressure of 1.29 atm and a volumeof 0.0152 m3, , is heated to a final state wherethe pressure is 6.29 atm and the volume is0.0552 m3.The gas constant is 8.31447 J/mol · K .Determine the change in entropy for thisarrow_forward4) A sample of argon at 01 atm pressure and 25C expands reversibly and adiabatically from 0.5 L to 1.0 L. Calculate its final temperature, the work done during the expansion, and the change in internal energy. The molar heat capacity of argon at constant volume is 12.48 JK-1mol-1.arrow_forward
- Question : Determine the units of the quantity s ̄/Ru, where s ̄ is the molar specific entropy and Ru is the universal gas constant. Explain your answer pleasearrow_forward(a) In reaching equilibrium, how much heat transfer occurs from 1.00 kg of water at 40.0º C when it is placed in contact with 1.00 kg of 20.0º C water in reaching equilibrium? (b) What is the change in entropy due to this heat transfer? (c) How much work is made unavailable, taking the lowest temperature to be 20.0º C ? Explicitly show how you follow the steps in the Problem-Solving Strategies for Entropy.arrow_forwardA closed rigid vessel contains 40% liquid water and 60% water vapor by volume. The liquid-vapor mixture is in equilibrium at 150°C. What is the quality of the mixture?arrow_forward
- In a motorcycle engine, a piston is forced down toward the crankshaft when the fuel in the top of the piston’s cylinder undergoes combustion. The mixture of gaseous combustion products then expands adiabatically as the piston descends. Find the average power in (a) watts and (b) horsepower that is involved in this expansion when the engine is running at 4000 rpm, assuming that the gauge pressure immediately after combustion is 15 atm, the initial volume is 50 cm3, and the volume of the mixture at the bottom of the stroke is 250 cm3. Assume that the gases are diatomic and that the time involved in the expansion is one-half that of the total cycle.arrow_forwardEstimate the Joule-Thomson coefficient for steam at 3MPA and 300°C using the steam tables. Estimate the Joule-Thomson coefficient for steam at 6MPA and 500°C using the steam tables. During phase change the Joule-Thomson coefficient is always positive or negative? Using gure A-14E (or A-14) in the tables of your book, is the Joule-Thomson coefficient ever negative for r134a? If so, where is it negative relative to temperature and pressure?arrow_forwardA two-phase, liquid–vapor mixture of H2O, initially at x=30% and a pressure of 100 kPa, is contained in a piston–cylinder assembly. The mass of the piston is 10 kg, and its diameter is 15 cm. The pressure of the surroundings is 100 kPa. As the water is heated, the pressure inside the cylinder remains constant until the piston hits the stops. Heat transfer to the water continues at constant volume until the pressure is 150 kPa. Friction between the piston and the cylinder wall and kinetic and potential energy effects are negligible. For the overall process of the water, determine the work and heat transfer, each in kJ.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY