Concept explainers
The advantage of using coil with many turns in Faraday’s experiments.
Answer to Problem 1Q
The advantage of using coil with many turns in Faraday’s experiment increases the values of the quantities to be experimentally measured.
Explanation of Solution
From the experiment shown in the Figure 29-1, Faraday concluded that a constant magnetic field does not produce current in the conductor, but a changing magnetic field can produce a current, this current is known as induced current. And also changing magnetic field induces an emf.
From the Faraday’s law, write the expression for induced emf if the circuit contains
Here,
Write the expression for induced current.
Here,
Use equation (I) in (II).
Equation (I) and (III) shows that, the induced emf and therefore induced current are proportional to number of turns.
Conclusion:
Therefore, the advantage of using coil with many turns in Faraday’s experiment increases the values of the quantities to be experimentally measured.
Want to see more full solutions like this?
Chapter 29 Solutions
EBK PHYSICS FOR SCIENTISTS & ENGINEERS
- (I) If the current to a motor drops by 12%, by what factordoes the output torque change?arrow_forwardIn electromagnetic induction, how does no. of coils affect the current produced?arrow_forward(i) Calculate the magnitude of the induced current in the circuit. (ii) State the direction of induced current in the metal bar.arrow_forward
- 3) A square loop circuit (with a 30.0 V battery, resistance of 6.00 ohms and side length of 2.00 m) is inside a uniform constant B-field as shown. B 450 a) There might be a mistake with the way B is drawn! The force due to the B-field on the circuit current is shown on one of the sides and is given by: F = 12.5NÎ – 12.5Nĵ Is the B-field drawn pointing in the right direction? Explain how you figured it out with 1 or 2 sentences. b) Find the magnitude of the magnetic field. c) You want to induce a current in the circuit to cancel the current created by the battery. You can do this by changing the B-field. dB needed? (also is it positive or negative?) dt What is the rate of change of the B-fieldarrow_forward(III) A simple generator has a square armature 6.0 cm on aside. The armature has 85 turns of 0.59-mm-diametercopper wire and rotates in a 0.65-T magnetic field. Thegenerator is used to power a lightbulb rated at 12.0 V and25.0 W. At what rate should the generator rotate toprovide 12.0 V to the bulb? Consider the resistance of thewire on the armaturearrow_forward3) A square loop circuit (with a 30.0 V battery, resistance of 6.00 ohms and side length of 2.00 m) is inside a uniform constant B-field as shown. B 450 There might be a mistake with the way B is drawn! メ The force due to the B-field on the circuit current is shown on one of the sides and is given by: F = 12.5Nî – 12.5Nĵ b) Find the magnitude of the magnetic field. ANarrow_forward
- II) For the electric power transmission system shown inFig. 21–25, what is the ratio for Ns/Np for (a) the step-up transformer, (b) the step-down transformer next to the home?arrow_forwardIn a stationary field coil of 500 turns calculate the induced voltage produced by the following flux changes: (a) 4 Wb increasing to 6 Wb in 1 s; (b) 4000 lines of flux increasing to 5000 lines in 5 µs; (c) 4 Wb remaining the same over 1arrow_forwardMagnetic induction at a distance 10 m from center of circular coil of area 1m² carrying 10 A is 2 × 10-9 T 4 x 10-6 T (a) (c) (b) 4 x 10:⁹ T (d) 10-6 Tarrow_forward
- Problem 7)) Consider a transformer, used to recharge rechargeable flashlight batteries, that has 500 turns in its primary coil, 4 turns in its secondary coil, and an input voltage of 120 V. Note that n = 4 (a) Given that the input current I(p) is 0.0256 A, to produce a 3.2 A output current, convert 0.0256 A to milliamps. I(p) = Part (c) What is the power input, in watts? (Explain thoroughly whether or not you use amps or milliamps for this calculation)arrow_forwardUsing information in Example 20.6, what would the Hall voltage be if a 2.00T field is applied across a 10-gauge copper wire (2.588 mm in diameter) carrying a 20.0-A current?arrow_forwardThe density of charge carriers far copper is 8.471028 electrons per cubic meter. What will be the Hall voltage reading from a probe made up of 3cm2cm1cm ( (LWT) ) copper plate when a current of 1.5 A is passed through it in a magnetic field of 2.5 T perpendicular to the 3cm2cm .arrow_forward
- Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax College
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning