Concept explainers
Name five changes that are made to air to condition it.
The five changes made to air for its conditioning.
Answer to Problem 1RQ
The five changes made to air for its conditioning is heating, cooling, humidifying, dehumidifying and cleaning.
Explanation of Solution
The atmospheric air contains a lot of impurities which can harm the human body in many ways. The normal atmospheric air contains moisture, odor, poisonous gases as well as dust particles, etc. Air conditioning is the process to remove these impurities from the air and make it clean to comfort the human body.
To clean air for conditioning it is necessary to make some changes. The major five changes that are required to make in the air for conditioning are listed below:
- Heating:
Atmospheric air is heated to higher temperatures to kill the bacteria and germs present in it.
- Cooling:
Heated air then cooled so that it can be adequate for human comfort.
- Humidifying:
Air is humidified to add some moisture in it.
- Dehumidifying:
Air is dehumidified to remove the excess moisture from it.
- Cleaning:
Cleaning of air includes removing any smell, bacteria and dust particles present in it.
Conclusion:
Thus, the five changes made to air for its conditioning is heating, cooling, humidifying, dehumidifying and cleaning.
Want to see more full solutions like this?
Chapter 37 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
- A _____________sample is taken from the flue gas tocheck the efficiency of a gas furnace.arrow_forwardMatch the correct advantage with the fluid power system.arrow_forwardSubject:TLE (Sorry for the b&w pic...) Draw the "coolant temperature gauge" indicating the middle temperature of an engine.arrow_forward
- A lawnmower stops running after a short period of time. The fuel tank filler cap is removed and an almost fuel tank of fuel is found, so the cap is reinstalled and the engine restarted. The engine runs again for a short time and then dies so the cap is removed again and the process repeats. Tech a says the problem may be due to a clogged vent in the fuel cap. The b says that the intake mainfold gasket may be defective. Who is correct?arrow_forwardFor every pound of pressure put on engine coolant, the boiling point of the coolant is raised about. 2°F(1.1°C) 3°F(1.6°C) 4°F (2.2°C) 5°F(2.7°C)arrow_forwardMatch the following correctly , need asap its urgentarrow_forward
- how did you get the 3038Pa in static pressure?arrow_forward2. Two sections must be discussed: 2.1. Talking about the material from which the air conditioner compressor is made with a presentation of the properties of the material 2.2. Preparing the executive drawing of the air conditioner compressor (job shop drawing) and it should include (dimensional and geometrical tolerances)arrow_forwardName the two basic types of compression gauges.arrow_forward
- Heat Excarrow_forwardWhat is the advantage of using an injector-type mixing chamber?arrow_forwardGiven two oil According to the standard by Society Automotive Engineers the oil , by comparing the 5W-30 with the 10W-30, a. The 5W-30 has lower viscosity than 10W-30 at low temperature. O b. The 5W-30 has higher viscosity at the high temperature. c. Both of the oils are suitable for cold weather O d. All of the above are true.arrow_forward
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning