Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
Chapter 40, Problem 1SA
To determine
The three ways for classification of CV joints.
Expert Solution & Answer
Answer to Problem 1SA
The three ways for classification are by position, by design and by function.
Explanation of Solution
The CV joints are classified in three ways which are:
- By Position − inboard or outboard.
- By Design − ball-type or tripod.
- By Function − fixed or plunge.
Conclusion:
Thus, these are the three classifications of CV joints.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
explain the operational difference between CV joints and universal joints. (50-80 words)
List the pros and cons of a compression spring ping pong ball launcher
Please select all that applies.
The possible failure modes for bolted joints are:
Oshear in the bolts
bearning of the bolts on the connected material
tension in the connected parts
Otorsion in the connected parts
Chapter 40 Solutions
Automotive Technology
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Similar questions
- materials used in friction clutch designarrow_forwardSketch and label power screw thread form (Acme thread). What is the functional difference between fastener thread forms and power-screw thread forms?arrow_forwardMake the definition of Spring Pin and what are the advantages and disadvantages?arrow_forward
- Use method of Joints for Darrow_forwardPlease select all that applies. The possible failure modes for bolted joints are: shear in the bolts bearning of the bolts on the connected material tension in the connected parts torsion in the connected partsarrow_forwardName 3 ways to maintain fatigue-prone componentsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning