PRACTICE PROBLEM 1 2.2 A Y-connected balanced three-phase generator with an impedance of 0.4+ j0.3 2 per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 2 per phase. The line joining the generator and the load has an impedance of 0.6 + j0.7 S2 per phase. Assuming a positive sequence for the source voltages and that Van = 120/30° V, find: (a) the line voltages, (b) the line currents. e-Text Main Menu | Textbook Table of Contents | Problem Solving Workbook Contents

PRACTICE PROBLEM 1 2.2 A Y-connected balanced three-phase generator with an impedance of 0.4+ j0.3 2 per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 2 per phase. The line joining the generator and the load has an impedance of 0.6 + j0.7 S2 per phase. Assuming a positive sequence for the source voltages and that Van = 120/30° V, find: (a) the line voltages, (b) the line currents. e-Text Main Menu | Textbook Table of Contents | Problem Solving Workbook Contents

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

Suppose you have a three-phase generator that provides 120 Vạc per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 Za -j20 ZA j 30 j 30 -j20 j3a -j20 Zo -j20 ZE j30 -j20 j 30. Assume the generator is star connected with no neutral, calculate the total power of the system and the total power factor. mm m
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
a. Y-Connected b. В 100kW Source 0.9 LAG 80KVA 0.8 LAG Figure 1 80kW 0.85 LAG
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. 10 ZA j 20 j30 Za j20 j30 j3Ω -j20 j3a -j2n Ze Zo •j20 j 30 j30. ZE -j20 Assume the generator is connected in delta, calculate the total power of the system and the total power factor.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.
Can you explain the given questions in an original way? Single Phase and Three Phase Principles • Single Phase Generators • Two Phase Generators
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
Two SGs are supplying a load by Pwad with 0.9 PF lagging. Gi has a no-load frequency of 54H2, and a slope Spi=1.1MW/Hz. G2 has a no-load frequency of 51HZ, and a slope Spz=1.1MW/Hz. If the system frequency is 50HZ: 1. How much power is supplied by each generator? 2. What is the load power Pload? 3. Draw the house-diagram for this system. 4. Find the system frequency, if the governor set points on G1 are decreased by 1Hz.
A 3-phase generator possesses a synchronous reactance of 62 (line reactance between the source and the load) and the excitation voltage Eo = 3KV (source) per phase. Calculate the line-to-neutral voltage ELoad for a balanced resistive load of 8. Also, draw a phasor diagram between three-phase source and load voltages.