Design a synchronous sequential circuit that counts in the following sequence 2,6,3,7,1 0,4, then repeats. Treat all unused states as don’t cares. Implement the design using a JK type flip-flop as the most significant flip-flop, a SR type flip-flop as the least significant flip-flop and a D type flip-flop for all remaining flip-flops.

Design a synchronous sequential circuit that counts in the following sequence 2,6,3,7,1 0,4, then repeats. Treat all unused states as don’t cares. Implement the design using a JK type flip-flop as the most significant flip-flop, a SR type flip-flop as the least significant flip-flop and a D type flip-flop for all remaining flip-flops.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the circuit goes through the state transitions from 00 to 10, to 01, to 11, back to 00, and repeats. When x_in = 1, the circuit will reverse the given sequence. a. Using D Flip-Flop. b. Using JK Flip-flop. Provide the state diagram, state table, state equations, and the circuit diagram.
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the state of the circuit remains the same. When x_in = 1, the circuit goes through the state transitions from 00 to 01, to 11, to 10, back to 00, and repeats. a. Using D Flip-Flop. b. Using JK Flip-flop.
Design a sequence detector that detects the sequence 1010. This detector has one input X, and one output Y. The output Y is set to 1 only when the input sequence for X is a 0 followed by a 0 by followed by another 0 and finally followed by a 1, detecting the sequence, otherwise the output Y is set to 0. Using D-type flip-flops in designing this detector. 1.Show the state diagram 2.Show the state table3. Draw the logic diagram of the designed device
5. A sequential circuit has two flip-flops A and B, one input X, and one output Y. The state diagram is shown in the following figure. Design the circuit with D flip-flops using a 1-hot state assignment. 00/1 01/0 11/0 10/0
Design a 2-bit counter using D-Flip flops with one input. When the input is 0, the ww m wwww w w m w i ww ww wwww www counter counts down, with the repeated sequence (11-10-01-00). When the input is 1, the counter counts repeated random sequence (00-01-11-10). a) Derive the state table for the sequential circuit. wwwww b) Derive the simplified flip flops input equations. www w w ww www m www ww c)Draw the logic circuit diagram of a 2-bit counter.
Question: The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, QO = 0,0,0 initially. a) Plot the clock, Q2, Q1 and QO until the outputs begin to repeat. b) Show the circuits acts as a counter 00 1000 Hz/50%
Design a D Flip-Flop using a JK Flip-Flop and basic gates.You have to show the followingi. The conversion tableii. The simplified equation(s) for the flip-flop input(s)iii. The final circuit diagram
Design a sequential circuit with 3 flip-flops and 1 input switch (X).If X=0, the circuit repeatedly follows the assigned sequence.And if X=1, the circuit will reverse its sequence. The sequence is 3, 7, 6, 5, 1, 4, 0, 2. Use D and JK Flip flop.
i need help please using j-k flip flop is fine Design a 3 bit sequential circuit using T-Flip Flops or Interconnected J/K Flip Flops. The states of the circuit should go from 0 > 6 > 2 > 3 > 5 > 0
The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, Q0 = 0, 0 , 0 initially. After how many cycles, the outputs of the flip-flops will repeat? Q' 1000 Hz/50% Q1 Q Q2
b) Using an SR latch and logic gates, design a T-N flipflop which has two input lines (T and N) and two output lines (Q and Q'). The flip-flop operates according to the following characteristics table. Determine the characteristics equations and draw circuit diagram. Inputs T Outputs Q(t+1) | Q'(t+1) Operation Reset No-Change Toggle Reset Q(t) Q'(t) Q'(t) Q() 1