For the following state table: Next State A* B* Output Current State AB X=0 X=1 00 10 00 0 1 00 11 1 10 01 11 1 11 10 01 1 a) Find the flip-flop input equations and the output equation for three different implementations that use D flip-flops, T flip-flops, and JK flip-flops. b) Draw the circuit diagram for the implementation that uses the JK flip-flops only.

For the following state table: Next State A* B* Output Current State AB X=0 X=1 00 10 00 0 1 00 11 1 10 01 11 1 11 10 01 1 a) Find the flip-flop input equations and the output equation for three different implementations that use D flip-flops, T flip-flops, and JK flip-flops. b) Draw the circuit diagram for the implementation that uses the JK flip-flops only.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).
Design the 4-bit Johnson Counter using D flip-flop as shown in the figure in the VHDL code. 4 Bit Johnson Counter using D FlipFlop él 9 CLOCK RESET FDC CUR 3 FDC FDC FDC
Redesign by using D flip-flops and give the state diagram for the logic circuit after the redesign. X J yi Z, K yi J y2 K clock
Design a 6-bit counter with control input using flip-flops. Every hour pulseIt should be a design that will increase or decrease by 4 when it arrives. Control input increment orwill determine the decrease. Increasing when control input is 0, decreasing when 1should be designed.
010 For the state diagram shown below. what is the Boolean expression of the flip-flop inputs if you assume that the circuit is built using T flip-flops. (Assume that the binary code is assigned in an ascending order for the states starting from state A). X is the external input.
Solve both Draw state diagram of a J-K flip flop. write Verilog code for JK flip flop
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the state of the circuit remains the same. When x_in = 1, the circuit goes through the state transitions from 00 to 01, to 11, to 10, back to 00, and repeats. a. Using D Flip-Flop. b. Using JK Flip-flop.
1 For the state diagram below a sequential circuit has 2 JK -flip-flops A(MSB) and B, one input variable X and one output function Y. 00/1 01/0 1 1 10/0 11/0
9 Two edge-triggered J-K flip-flops are shown in The Figure. If the inputs are as shown, draw the Q output of each flip-flop relative to the clock, and explain the difference between the two. The flip-flops are initially RESET. CLK CLK-C CLK C K (a) (b)
Design a 4-bit counter C( represented by C3C₂C₁C₁)which can count the specified sequence as following: 0000011010010010 ➜ 11000000. The counter will use the falling edge of the clock (denoted by Clk) and have a separate reset pin (R) which will reset the counter to 0000 when it is low (e.g. = 0). Please use D type Flip-flops. Write down the state diagram, and state table; Use K-map to simplify the input equations; Write down the simplified input equations and draw a neat circuit diagram. (Hint: use don't care for unused states)
The following diagram shows how to build a T flip-flop with EN using a D flip-flop. Design a circuit that is equivalent to a D flip-flop using a T flip-flop with EN. Draw the circuit diagram.
Design a D Flip-Flop using a JK Flip-Flop and basic gates.You have to show the followingi. The conversion tableii. The simplified equation(s) for the flip-flop input(s)iii. The final circuit diagram