Mark Billiards. Consider two #identical billiard balls (I = mR²) with mass 0.160 [kg] and radius 0.0250 [m] that have the same energy. If first billiard ball is rolling without slipping and the second billiard ball is undergoing pure linear motion with velocity 4.00 [m/s], is the angular velocity of the first billiard ball? at i O 135 [rad/s] O 119 [rad/s] O 113 [rad/s] O 160 [rad/s]

Mark Billiards. Consider two #identical billiard balls (I = mR²) with mass 0.160 [kg] and radius 0.0250 [m] that have the same energy. If first billiard ball is rolling without slipping and the second billiard ball is undergoing pure linear motion with velocity 4.00 [m/s], is the angular velocity of the first billiard ball? at i O 135 [rad/s] O 119 [rad/s] O 113 [rad/s] O 160 [rad/s]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solving dynamics problems in steps: 1. Collect data and assumptions 2. Desired result? 3. Make drawing/sketch of the (sub)problem 4. Equations and calculations 5. Answer and conclusions Furthermore: - Write down the steps clearly Check intermediate results (accuracy) Dimension check and units! Magnitude of number in line with expectation?
(The complete question is in the picture) A disk rotates with constant angular acceleration about an axis passing through its center of mass. At an instant, its angular speed is measured to be 20.0 [rad/s]. What is the angular speed of the disk after 2.00 [s] if it has revolved by 60.0 [rad] during this timeinterval? A. 10.0 [rad/s]B. 20.0 [rad/s]C. 30.0 [rad/s]D. 40.0 [rad/s]
The rotating blade of a blender turns with a constant angular acceleration 1.50 [rad/s^2].a. How much time does it take to reach an angular velocity of 36.0 [rad/s^2] starting from rest? b. Through how many revolutions does the blade turn in this time interval? c. What are the tangential acceleration and tangential speed of an ant sitting on the blade 10.0 cm from the axis of rotation during the end of this interval? d. What is the moment of inertia of the ant if its mass is 10.0 g? e. What is the rotational kinetic energy of the ant?
A bar is pinned to ground at its O with the bar rotating clock-wise at a constant rate of Ω=8.9[rad/s]. Block P is traveling to the left along a straight path towards with a constant speed of vp=9.7 [ft/s]. Given that h=4.7[ft] and rA/O=1.2[ft], solve the following: What is the J^ component of v¯A? What is the J^ component of (v¯P/A)rel? What is the I^ component of (v¯P/A)rel? What is the ω of the local coordinate system (this is the ω in the relative velocity and acceleration equations.
The force F (in newtons) of a hydraulic cylinder in a press is proportional to the square of sec x, where x is the distance (in meters) that the cylinder is extended in its cycle. The domain of F is [0, /3], and F(0) = 500. (a) Find F as a function of x. (b) Find the average force exerted by the press over the interval [0, /3]
The rotating blade of a blender turns with a constant angular acceleration 1.50 [rad/s^2].a. How much time does it take to reach an angular velocity of 36.0 [rad/s^2] starting from rest? Through how many revolutions does the blade turn in this time interval? b. What are the tangential acceleration and tangential speed of an ant sitting on the blade 10.0 cm from the axis of rotation during the end of this interval? c. What is the moment of inertia of the ant if its mass is 10.0 g? What is the rotational kinetic energy of the ant?
1)The mutual forces of gravitation depends on the law of action and reaction. [T or F] 2)The radius of gyration kx means the area concentrated into ring strip by y-axis [T or F] 1)we get concurrent forces, if there are three forces lines of action intersect at one point.[T or F]
You must select a submerged centrifuge multicellular pump for a borehole on a worksite that requires a flow of 1.500l/s. The borehole itself is 150m deep (see figure 5). If the outlet pipe has the following properties, then: wwww wwwwwww Water outlet (open air) wwww Outlet pipe L = 200m Borehole wwwww Pump f= 0.04 D = 38mm Figure 5 Borehole and pumping schematic A) Choose a pump from those presented in figure 6 (you must select the most adequate model) if there is no local head-loss, only friction related head-loss. You must draw the complete characteristic curve for the pipe directly on figure 6.; B) Is cavitation an issue if NPSHrequired is 5m briefly discuss the results. C) Determine the supplied power output by the pump (in kW) as well as the absorbed power output when the pump reaches it's operational flow for the pump you have selected. | N.B. Hypothesize that water in the borehole is level with the pump intake. The pump intake is the same diameter as the outlet pipe. Patm-100…
A particle of mass 0.102 kg is rotating at 840 rpm at a radius of 135 mm. At t=2 the radius begins to expand at a rate of 14 mm.s-1. What is the radial force at t=1.9s [N] What is the arc length traveled by the mass at t=1.9 s? [m] What is the transverse force on the mass at t=4s? [N]
The rod A rotates in the horizontal plane (xy- plane) t3 with 0=- 2 [rad). The collet B (Bilezik) moves outward through the rod with r= 80 t² [mm]. Time t is given in seconds, when time t=1 sec determine, a) the velocity and direction of the collet B? b) the acceleration and direction of the collet B? B
4-6- SI A six-liter, eight-cylinder, four- Stroke cycle race car engine operates at 6000 RPM using stoichio- metric nitromethane as fuel. Combustion efficiency. is 99%, and the fuel input rate is 0.198 kg/see. a- Volumetric efficiency of the engine [!] b-Flow rate of air into the engine. [ kg/sec.:] Calculate :
A pendulum that is powered via a series elastic actuator can be modelled as follows (simplified): Jy (double dot) + By (dot) + K(y-u) + mglsin (y) where y is output and u is input = = 0 j = 0.2 [kgm^2] (Inertia) to XL. K = 60 [N.m/rad] (Spring stiffness) B 0.05 [N.m.s/rad] (damping coefficient) g 9.81 [m/s^2] (gravitational acceleration) m = 2.5 [kg] (mass) 1 0.5 [m] (pendulum length) = = yo = 0.25 [rad] y0 (dot) = -0.2 [rad/s] Simulate mechanical system using Matlab/Simulink when the input is a unit step Using a scope, plot the input and output.