Q24. For the system shown in the figure Q24, Obtainthe closed loop transfer function,damping rationatural frequencyexpression for the output response if subjected to unit responsei.ii.ii.iv.C(s)20R(s)(s+ 1) (s + 4)Figure Q24

Given open loop transfer function is G(s)=20(s+1)(s+4)=20s2+5s+4 Feedback given is unity feedback.…

Q24. For the system shown in the figure Q24, Obtain i the closed loop transfer function, ii i. damping ratio iii. natural frequency iv. expression for the output response if subjected to unit response 20 R(s) (s + 1) (s + 4) Figure Q24

Q24. For the system shown in the figure Q24, Obtain i the closed loop transfer function, ii i. damping ratio iii. natural frequency iv. expression for the output response if subjected to unit response 20 R(s) (s + 1) (s + 4) Figure Q24

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Illustrate the operation of impulse voltage generation using Marx circuit. The scematic diagram of Marx circuit arrangement need to be included and explained.
OL. Simplify the block diagram shown in Figure(I) and obtain the elosed- loop transfer function C(s) R(s) Ris) Figuret1)
(a) (b) Vin R₁ www ww R₂ Figure Q4 - Vout Derive the gain of the circuit shown in Figure Q4 showing all steps and assumptions. What type of circuit is this? Explain how the circuit could be changed or operated in order to use it as a voltage controlled current source, derive the transfer function.
Vs RE www 2₁ www Rc1 11 Vcc RC2 Q₂ RF Q3 +₁ -O V₂ Sketch the feedback small signal model of this circuit.
4. Consider the RC circuit in Figure 1.4. Let us consider a system whose input is the input voltage vin (t) and the output is the voltage across the capacitor vout (t). Find an integral equation that relates the input and output signals. Draw a block diagram showing a different realization (implementation) of this system using integrators, multipliers and adders.
r:09 A moodle1.du.edu.om An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 O c. 0.2356 and 0.5625 O d. 0.5215 and 0.5625 Previous page Next page 1 Aşsignmen
Q4 Consider you have to design a convertor to produce an output voltage of 36 V from a 3.3-V input DC source. The output current is 0.1 A. The design of above convertor should be for the output ripple voltage of 2 percent. The effect of ESR should be considered having relation to the capacitor value by as, rc = 10-5/c Design the convertor subject to above mentioned design requirements and justify why a boost convertor will not be a good choice here.
(b) Consider the above bock-diagram of figure (2a). You are now required to derive the transfer function, Y(s)/R(s), by using the signal flow graph method. Label in your working, the paths and loops associated with the block-diagram. (c) Determine the system transfer function for the following signal-flow diagram of figure (2b). " - H, R(s) Y(s) 1/s G, G2 G, G. H2 Figure (2a)
7 7 76% Q4. Figure 4 shows a circult diagram of the Wien-bridge oscillator. ASsume that the amplifier employed is an ideal op-amp. a) State the Barkhausen criterion for sustained oscillation. b) Explain briefly how the phase shift requirement for sustained oscillation is met in this circuit. c) The feedback ratio of the circuit shown in Figure 4 is given by, %3D 3R +j(2afCR-C) 27/ Derive the expression for the oscillation frequency, f. R. Figure 4 Colpitts oscillator - 7x-
Using Mason's gain formula calculate the closed-loop transfer function for the system described by the following equations: Y2= Y1– H1Y3– H3Y5 Y3 = G1Y2– H4Y4 Y4 = G2Y3 + G4Y2 %3D Y5 = G3Y4 Y6 = Y5
Project # 3 (Use a FET op-amp) You’ve been working with an implementation team to build the following components of a system: The system consists of a DC power supply, filters, instrumentation amplifier, one-state system and A/D converter.  Build an AC/DC dual power supply circuit that draws a 55Vp-p sinusoidal voltage, to provide a dc output voltage of +10 V. Find the proper data sheet of the IC regulator and specify ranges of output current and voltage. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?  Build a 4th order Butterworth LP filters that cover a signal range 10kHz and a gain of 100V/V each. Use C = 0.01µF with proper values of R’s. Record your findings and include plots (magnitude and phase. Calculate the roll-off of the filter.  Build an instrumentation amplifier having a differential gain of 50V/V. Choose the right differential input and common input signals to…
on to Electronic Analysis and Design-C urses / Introduction to Electronic Analysis and Design - C The difference between Vcs and vGs is Select one: a. The first is ac and the second is de b. The first is ac and the second is ac + de c. The first is de and the second is ac + dc d. The first is de and the second is ac