Situation 5: A W4x13 has a length of 3.5 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 2,470 mm^2 d = 106 mm bf = 103 mm tf = 8.76 mm kdes 15.1 mm tw = 7.11 mm rx = 43.7 mm ry = 25.4 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 287 KN O 268 KN O 310 KN O 325 KN

Situation 5: A W4x13 has a length of 3.5 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 2,470 mm^2 d = 106 mm bf = 103 mm tf = 8.76 mm kdes 15.1 mm tw = 7.11 mm rx = 43.7 mm ry = 25.4 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 287 KN O 268 KN O 310 KN O 325 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 1: A W8x67 has a length of 7.50 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 12,700 mm^2 d = 229 mm bf = 210 mm tf = 23.7 mm kdes = 33.8 mm tw = 14.5 mm rx = 94.5 mm ry = 53.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are pinned? O 678 KN O 667 KN O 740 KN O 652 KN
Situation 1: A W8x67 has a length of 7.50 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 12,700 mm^2 d = 229 mm bf = 210 mm tf = 23.7 mm kdes = 33.8 mm tw = 14.5 mm rx = 94.5 mm ry=53.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? O 1143 KN O 1106 KN O 1058 KN O 1199 KN
Compute the area of steel for the L-section shown in the figure if it is subjected to M₁ = 120 kN.m feu = 35 N/mm² and fy = 400 N/mm² 400 mm 600 mm 120 mm 100 T IS456
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
A beam carries a concentrated load W and a total uniformly distributed load of 4W as shown in the figure. What safe load W can be applied if o ≤ 120 MPa and a ≤ 80 MPa? Can a greater load be applied if the ot section is inverted? Explain. W 2 m R₁ 4W 4 m R₂ 75 mm TE ΝΑ 125 mm INA= 24 x 10 mm
A RC column of square cross-section (400 x 400 mm2) has its column load-moment interaction diagram as shown in figure below. PulfabD 0.2 MulfbD² 0 0.2 0.3 What is the maximum uniaxial eccentricity at which a factored load P = 640 kN can be applied safely? (Take fk = 20 MPa) U (a) 300 mm (b) 400 mm (c) 600 mm (d) 800 mm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B1 in kN. 35KN В1 B2 ВЗ 10KN 15KN 30KN
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN В1 B2 B3 10KN 15KN 30KN
Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf = 148 mm tf = 13 mm kdes = 7.62 mm tw = 14.5 mm rx = 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 660 KN 641 KN 667 KN O 600 KN
1. The aluminum bar of cross-se ctional are a 0.6 in.2 carries the axial loads shown in the fig ure. Compute the total change in length, in inches, of the bar given that E = 10 x 106 psi. 6000 lb 4000 lb 7000 lb 5000 lb + 3 ft 5 ft to 4 ft Total change in length (in ches)
Drive an expression for the total extension of the bar of circular cross-section as shown when it's Subjected to an axial tensile lead (P).
Activity 3 Problem Set Question Locate the plastic centroid of the section shown below. Dimensions are in meters. Your reference axes are the leftmost and topmost edge of the flange. 2Ø12 fy = 350 MPa 0.650 1 Ø12@150 stirrups 5Ø25 fy = 390 MPa 0.250 0.450 0.150