Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 3, Problem 3.58P
An electrical current of 700 A flows through a stainless steel cable having a diameter of 5 mm and an electrical resistance of
- If the cable is bare. what is its surface temperature?
- If a very thin coating of electrical insulation is applied to the cable. with a contact resistance of
- There is some concern about the ability of the insulation to withstand elevated temperatures. What thick-ness of this insulation
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Question 1: A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 20 oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.
You want to figure out whether it is safe to touch the outside
surface of the pipe in question. Here are the details: "A stainless steel pipe is carrying hot water to a
test facility. The inside surface of the pipe is at a temperature of 70°C and the inner radius is 0.2 m.
The thickness of the steel pipe is 12 mm. It is exposed to air at 30°C on the outside. The average
convection coefficient of air over the pipe is 15 W/m².°C. Thermal conductivity of steel is 54 W/m.°C.
Negelect radiation. Consider steady conditions." Calculate, assuming a 1-m long pipe segmen, the
temperature of the outside surface of the pipe.
Question 4
The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K.
A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer
coefficients on the outer surface of the window to be 12 W/m²-K.
Take appropriate assumptions while solving this problem.
(a)
T₁=15°C
TA
-A- 1m x 3m = 3m²,
k=1.4W/m-K
-T₂=5°C
L=0.005m
Figure Q2
Determine the heater thermal load to maintain the room temperature?
Chapter 3 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 3 - Consider the plane wall of Figure 3.1, separating...Ch. 3 - A new building to be located in a cold climate is...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - A dormitory at a large university, built 50 years...Ch. 3 - In a manufacturing process, a transparent film is...Ch. 3 - The walls of a refrigerator are typically...Ch. 3 - A t=10-mm -thick horizontal layer of water has a...Ch. 3 - A technique for measuring convection heat transfer...Ch. 3 - The wind chill, which is experienced on a cold,...
Ch. 3 - Determine the thermal conductivity of the carbon...Ch. 3 - A thermopane window consists of two pieces of...Ch. 3 - A house has a composite wall of wood, fiberglass...Ch. 3 - Consider the composite wall of Problem 3.13 under...Ch. 3 - Consider a composite wall that includes an...Ch. 3 - Work Problem 3.15 assuming surfaces parallel to...Ch. 3 - Consider the oven of Problem 1.54. The walls of...Ch. 3 - The composite wall of an oven consists of three...Ch. 3 - The wall of a drying oven is constructed by...Ch. 3 - The t=4-mm-thick glass windows of an automobile...Ch. 3 - The thermal characteristics of a small, dormitory...Ch. 3 - In the design of buildings, energy conservation...Ch. 3 - When raised to very high temperatures. many...Ch. 3 - A firefighter's protective clothing, referred to...Ch. 3 - A particular thermal system involves three objects...Ch. 3 - A composite wall separates combustion gases at...Ch. 3 - Approximately 106 discrete electrical components...Ch. 3 - Two stainless steel plates 10 mm thick are...Ch. 3 - Consider a plane composite wall that is composed...Ch. 3 - The performance of gas turbine engines may be...Ch. 3 - A commercial grade cubical freezer, 3 m on a side,...Ch. 3 - Physicists have determined the theoretical value...Ch. 3 - Consider a power transistor encapsulated in an...Ch. 3 - Ring-porous woods, such as oak, are characterized...Ch. 3 - A batt of glass fiber insulation is of density...Ch. 3 - Air usually constitutes up to half of the volume...Ch. 3 - Determine the density, specific heat, and thermal...Ch. 3 - A one-dimensional plane wall of thickness L is...Ch. 3 - The diagram shows a conical section fabricated...Ch. 3 - A truncated solid cone is of circular cross...Ch. 3 - From Figure 2.5 it is evident that, over a wide...Ch. 3 - Consider a tube wall of inner and outer radii ri...Ch. 3 - Measurements show that steady-state conduction...Ch. 3 - A device used to measure the surface temperature...Ch. 3 - A steam pipe of 0.12-m outside diameter is...Ch. 3 - Consider the water heater described in Problem...Ch. 3 - To maximize production and minimize pumping costs....Ch. 3 - A thin electrical heater is wrapped around the...Ch. 3 - A stainless steel (AISI 304) tube used to...Ch. 3 - A thin electrical heater is inserted between a...Ch. 3 - A 2-mm-diameter electrical wire is insulated by a...Ch. 3 - Electric current flows through a long rod...Ch. 3 - A composite cylindrical wall is composed of two...Ch. 3 - An electrical current of 700 A flows through a...Ch. 3 - A 0.20-m-diameter. thin-walled steel pipe is used...Ch. 3 - An uninsulated. thin-walled pipe of 100-mm...Ch. 3 - Steam flowing through a long. thin-walled pipe...Ch. 3 - A storage tank consists of a cylindrical section...Ch. 3 - Consider the liquid oxygen storage system and the...Ch. 3 - A spherical Pyrex glass shell has inside and...Ch. 3 - In Example 3.6. an expression was derived for the...Ch. 3 - A hollow aluminum sphere. with an electrical...Ch. 3 - A spherical tank for storing liquid oxygen on the...Ch. 3 - A spherical, cryosurgical probe may be imbedded in...Ch. 3 - Prob. 3.70PCh. 3 - Prob. 3.71PCh. 3 - A composite spherical shell of inner radius...Ch. 3 - The energy transferred from the anterior chamber...Ch. 3 - The outer surface of a hollow sphere of radius r2...Ch. 3 - A spherical shell of inner and outer radii r1 and...Ch. 3 - Prob. 3.76PCh. 3 - Prob. 3.77PCh. 3 - Prob. 3.78PCh. 3 - The air inside a chamber at T,i=50C is heated...Ch. 3 - Prob. 3.80PCh. 3 - A plane wall of thickness 0.1 m and thermal...Ch. 3 - Large, cylindrical bales of hay used to feed...Ch. 3 - Prob. 3.83PCh. 3 - Consider one-dimensional conduction in a plane...Ch. 3 - Consider a plane composite wall that is composed...Ch. 3 - An air heater may be fabricated by coiling...Ch. 3 - Prob. 3.87PCh. 3 - Consider uniform thermal energy generation inside...Ch. 3 - A plane wall of thickness and thermal conductivity...Ch. 3 - A nuclear fuel element of thickness 21, is covered...Ch. 3 - In Problem 3.79 the strip heater acts to guard...Ch. 3 - The exposed surface (x=0) of a plane wall of...Ch. 3 - A quartz window of thickness L serves as a viewing...Ch. 3 - For the conditions described in Problem 1.44....Ch. 3 - A cylindrical shell of inner and outer radii, ri...Ch. 3 - The cross section of a long cylindrical fuel...Ch. 3 - A long cylindrical rod of diameter 200 mm with...Ch. 3 - A radioactive material of thermal conductivity k...Ch. 3 - Radioactive wastes are packed in a thin-walled...Ch. 3 - Radioactive wastes (ktw=20W/mK) are stored in a...Ch. 3 - Unique characteristics of biologically active...Ch. 3 - Consider the plane wall, long cylinder, and sphere...Ch. 3 - One method that is used to grow nanowires...Ch. 3 - Consider the manufacture of photovoltaic silicon,...Ch. 3 - Copper tubing is joined to a solar collector plate...Ch. 3 - A thin flat plate of length L thickness t. and...Ch. 3 - The temperature of a flowing gas is to be measured...Ch. 3 - A thin metallic wire of thermal conductivity k,...Ch. 3 - A motor draws electric power Pelec from a supply...Ch. 3 - Consider the fuel cell stack of Problem 158. The...Ch. 3 - Consider a rod of diameter D, thermal conductivity...Ch. 3 - A carbon nanotube is suspended across a trench of...Ch. 3 - A probe of overall length L=200mm and diameter...Ch. 3 - A metal rod of length 2L diameter D, and thermal...Ch. 3 - A very long rod of 5-mm diameter and uniform...Ch. 3 - From Problem 1.71, consider the wire leads...Ch. 3 - Turbine blades mounted to a rotating disc in a...Ch. 3 - Prob. 3.127PCh. 3 - Prob. 3.128PCh. 3 - Prob. 3.129PCh. 3 - A brass rod 100 mm long and 5 mm in diameter...Ch. 3 - The extent to which the tip condition affects the...Ch. 3 - A pin fin of uniform. cross-sectional area is...Ch. 3 - The extent to which the tip condition affects the...Ch. 3 - A straight tin fabricated from 2024 aluminum alloy...Ch. 3 - Triangular and parabolic straight tins are...Ch. 3 - Two long copper rods of diameter D=10mm are...Ch. 3 - Circular copper rods of diameter D=1mm and length...Ch. 3 - During the initial stages of the growth of the...Ch. 3 - Consider two long, slender rods of the same...Ch. 3 - A 40-mm-long, 2-mm-diameter pin fin is fabricated...Ch. 3 - An experimental arrangement for measuring the...Ch. 3 - Finned passages are frequently formed between...Ch. 3 - The fin array of Problem 3.142 is commonly found...Ch. 3 - An isothermal silicon chip of width W=20mm on a...Ch. 3 - As seen in Problem 3.109, silicon carbide...Ch. 3 - A homeowner's wood stove is equipped with a top...Ch. 3 - Water is heated by submerging 50-mm-diameter,...Ch. 3 - As a means of enhancing heat transfer from...Ch. 3 - Consider design B of Problem 3.151. Over time....Ch. 3 - Determine the percentage increase in heat transfer...Ch. 3 - Aluminum fins of triangular profile are attached...Ch. 3 - An annular aluminum fin of rectangular profile is...Ch. 3 - Annular aluminum fins of rectangular profile are...Ch. 3 - It is proposed to air-cool the cylinders of a...Ch. 3 - Prob. 3.165PCh. 3 - Prob. 3.166PCh. 3 - Prob. 3.168PCh. 3 - Prob. 3.173PCh. 3 - Prob. 3.174PCh. 3 - Prob. 3.175PCh. 3 - A nanolaminated material is fabricated with an...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A furnace wall is constructed of an inner layer of 12.7 mm of refracter material, a middle layer of 101.6 mm of insulation material and outer layer of 76.2 mm of steel. The wall surface temperature is 1370 °C inside the refracter material (T0) and 37.8 °C at the outside surface of the steel (T3). Use thermal conductivity for refractor kref = 6.64 W/mK, for insulation, kins= 2.34 W/mK and for steel kste = 45 W/mK. Calculate the heat loss in W for 1 m2 (heat flux)? The temperature at the inter face between the insulation material and steel board?arrow_forwardA spherical container of negligible thickness holding a hot fluid at 140oC and having an outer diameter of 0.4 m is insulated with three layers of each 50 mm thick insulation of k1 = 0.02: k2 = 0.06 and k3 = 0.16 W/m-K. (Starting from inside). The outside surface temperature is 30oC. Determine the Interface temperatures of insulating layers.arrow_forwardThe wall of a furnace is made up of a material which has thermal conductivity of 2.65 W/m◦C and a thicknesses 300 mm. The inner side of the furnace wall is exposed to hot gases at 1200 ⁰C with a convection coefficient of 20 W/m2⁰C and the inside the surface is at 700 ⁰C. The air outside the furnace is at 20⁰C with a convection coefficient of 15 W/m2⁰C. Draw a clear diagram representing the system Determine the temperature of the outside surface of the furnace The rate of heat loss from the furnace.arrow_forward
- A large steel plate having a thickness of L = 4 in, thermal conductivity of k= 7.2 Btu/h·ft. °F, and an emissivity of ε = 0.7 is lying on the ground. The exposed surface of the plate at x = L is known to exchange heat by convection with the ambient air at T∞ = 90°F with an average heat transfer coefficient of h = 12 Btu/h·ft².°F as well as by radiation with the open sky with an equivalent sky temperature of Tsky =480 R. Also, the temperature of the upper surface of the plate is measured to be 80°F. Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the plate, (b) obtain a relation for the variation of temperature in the plate by solving the differential equation, and (c) determine the value of the lower surface temperature of the plate at x = 0. Tsky h, To Convection Radiation XA 80°F L E Plate 0 Groundarrow_forwardA container, spherical in shape, with an outside diameter of 30 cm holds a hot fluid at 180°C. The container is insulated with two layers of each 10 cm thick of insulation of k = 0.05 and k2 = 0.20 W/mK (starting from inside). If the interface temperature between the first and second layer of insulation is 50°C, what is the rate of heat transfer through the container in Watts? Also, determine the outside surface temperature of the second layer of insulation.arrow_forwardThe surface of a furnace wall is at temperature of 1350°C. The outsidewall temperature is 42°C. The furnace wall is made of 25 cm of refractory material having a thermal conductivity of 1.4 W/m-K. The outside wall is steel, 1 cm thick with thermal cnoductivity of 47 W/m-K. Calculate the thickness in meter of brick to be installed in between the refractory material and steel if its thermal conductivity 0.28 W/m-K and the heat loss is not to exceed 750Wm²-K. O 0.513 O 0.438 O 0.402 O 0.481arrow_forward
- Required information Consider an electrically heated brick house (k = 0.40 Btu/h-ft-°F) whose walls are 9 ft high and 1 ft thick. Two of the walls of the house are 50 ft long and the others are 35 ft long. The house is maintained at 70°F at all times while the temperature of the outdoors varles. On a certain day, the temperature of the Inner surface of the walls is measured to be at 64°F while the average temperature of the outer surface is observed to remain at 45°F during the day for 10 h and at 35°F at night for 14 h. 35 ft 50 ft 9 ft Determine the amount of heat lost from the house that day. (You must provide an answer before moving on to the next part.) The amount of heat lost from the house that day is [ 18526 Btu.arrow_forwardA thermometric well is placed in a pipe having diameter of 55 mm. Pipe wall temperature is 100°C and heat transfer coefficient inside the pipe is 300 W/m² K. Thickness of thermowell is 1.2 mm and its length is 50 mm. Thermal conductivity of thermowell material. Is 30 W/mK. If the temperature of the gas flowing through the pipe is recorded by thermometer as 200°C, determine the true temperature of gas. If the error in gas temperature is to be reduced by 80% by increasing the length of thermowell, determine the new length of thermowell. Draw a sketch of this thermowell. Take perimeter to area ratio for thermowell as 1/T (T= thickness).arrow_forwardThe emissivity of galvanized steel sheet, a common roofing material, is ε = 0.13 at temperatures around 300 K, while its absorptivity for solar irradiation is αS = 0.65. Would the neighborhood cat be comfortable walking on a roof constructed of the material on a day when GS = 750 W/m2, T∞ = 16°C, and h = 7 W/m2 · K? Assume the bottom surface of the steel is insulated.arrow_forward
- A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 9oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.arrow_forwardQuestion 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K. A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer coefficients on the outer surface of the window to be 12 W/m²-K. Take appropriate assumptions while solving this problem. (a) T₁-15°C TA -A=1m x 3m 3m², k=1.4 W/m-K I L=0.005m Figure Q2 ** -T₂=5°C Find the convection heat transfer coefficients on the inner surface of the window.arrow_forwardThe section of a vertical wall is made up of fiberglass insulation slabs separated by wooden studs. The thermal conductivity of fiberglass and wood are 0.04 W/m-K and 0.18 W/m-K, respectively. The thickness of the wall is 160 mm. The temperatures of the inner and outer surfaces of the wall section are 22 °C and 4 °C, respectively. The ratio of the insulation area to the total wall area is 0.8. Calculate the total heat flow rate (in W/m2) through the wall per unit area. Wooden Stud Fiberglass Insulation Round your answer to 2 decimal places. Add your answer Follow-up question to Question 4, calculate the rate of heat flow (in W/m2) through unit area of studs. Round your answer to 2 decimal places.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license