Concept explainers
The load required for each step.
Answer to Problem 2.91P
The load required in intermediate step is
Explanation of Solution
Given:
The initial height of the cylinder is
The intermediate height of the cylinder is
The final height of the cylinder is
The initial diameter of the cylinder is
Formula used:
The expression for the intermediate diameter is given as,
The expression for the final diameter is given as,
The expression for intermediate cross-sectional area is given as,
The expression for final cross-sectional area is given as,
The expression for true stress at intermediate step is given as,
The expression for true stress at finalstep is given as,
The load required at intermediate step is given as,
The load required at final step is given as,
Calculation:
The true strain for intermediate step calculated is,
The true strain for final step calculated is,
Refer to table 2.2 for aluminium
The intermediate step diameter can be calculated as,
The final step diameter can be calculated as,
The intermediate step cross-sectional area can be calculated as,
The final step cross-sectional area can be calculated as,
The true stress at final step can be calculated as,
The true stress at intermediate step can be calculated as,
The load required for intermediate step can be calculated as,
The load required for final step can be calculated as,
Conclusion:
Therefore, the load required in intermediate step is
Want to see more full solutions like this?
Chapter 2 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
- The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same plot, but with different scale). This steel is used to make a rod that is 6 mm in diameter and 400 mm long. The rod is loaded in tension until an elongation of 1.2 mm is reached. A. Estimate the Yield Stress for the Steel. B. Estimate the Ultimate Tensile Stress for the Steel. C. Estimate the Elastic Modulus for the Steel. D. Estimate the %Elongation for the Steel. E. Estimate the Force acting on the rod necessary to achieve an elongation of 1.2mm. F. After an elongation of 1.2mm the load on the rod is removed. Estimate the length of the rod after the load is released. 600 500 400 500 400 300 300 200 200 100 100 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain Stress (MPa) Stress (MPa)arrow_forwardQuestion: Of course a wire with a cross-sectional area of one square meter is not a wire, but an extremely big block. So, compute the maximum load (in Newton) a round wire of this steel with a diameter d of 1 centimeter can have just before it breaks. Give your answer in 4 significant figures. Solution: Narrow_forwardFind the Brinell hardness number of the material if the indenter diameter is 10mm and the produced indentation was 5.12mm. The standard load of 3000kE was applied. (attach your solution)arrow_forward
- Problem 6: A circular metal rod of diameter 1 cm is loaded in tension. The extension of a 25 cm is measured accurately and is 0.0227 cm when the tensile is 5kN. Estimate the value of Young's modulus of the metal.arrow_forwardA cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a steel alloy that has a yield stress of 340 MPa. The internal pressure is 1.5 MPa. 1. Calculate the tangential stress in the cylinder in MPa. 2. Calculate the longitudinal stress in the cylinder in MPa. 3. Calculate the allowable pressure in MPa if a factor of safety of 2.0 with respect to yield is required. Kindly answer all numbers with complete solution. Needed ASAParrow_forwardProblem 1 An axially loaded bar shown in Fig. 1 has a stress concentration factor of 2.9 at the fillet. The proportional limit of the material is 55,000 psi. (a) Compute the nominal (average) stress in the following sections and state whether or not the stress is in the elastic range: (i) AB and (ii) BC. (b) (1) Compute the maximum stress (occurs in the region of the fillet). (i1) Will the material in the region of the fillet become plastic? 0.15 in. 1300 1b 4300 1b 3 in. 1 in. Fig. 1arrow_forward
- What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?arrow_forwardIn Figure 1, with its dimensions, loading status and material properties, different full circle cross-section rod has been given. The AB part of the rod is steel, 100 mm in diameter; BC part is copper and its diameter It is 80 mm. (a) Draw the normal force diagram of the bar. (b) Calculate the normal stresses to occur in parts AB and BC. (c) Calculate the total length change of the rod. çelik=steel , bakır=copper L4(cm)=230 , L5(cm)=240 , P1(kN)=124 , P2(kN)=58arrow_forwardIn Figure 1, with its dimensions, loading status and material properties, different full circle cross-section rod has been given. The AB part of the rod is steel, 100 mm in diameter; BC part is copper and its diameter It is 80 mm. (a) Draw the normal force diagram of the bar. (b) Calculate the normal stresses to occur in parts AB and BC. (c) Calculate the total length change of the rod. çelik=steel , bakır=copper , şekil 1 = figure 1 L4(cm)=230 , L5(cm)=240 , P1(kN)=124 , P2(kN)=58arrow_forward
- Calculate the stress developed in a steel rod that is 25 mm in diameter when a 70kNaxial tensile load is applied. Give your answer in four significant figures with MPaunits. Only include a numerical answer with no units.arrow_forwardA bar is applied a tensile load of 50 kN having diameter 10 mm, Calculate the tensile stress induced in the bar.arrow_forwardA 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force tangent to pulley rim in kN will crush the key if bearing stress is 50 ksi? Assume key and shaft are of the same material.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY