Principles of Instrumental Analysis
7th Edition
ISBN: 9781305577213
Author: Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
Chapter 31, Problem 31.5QAP
Interpretation Introduction
Interpretation:
Two techniques for characterizing the oil sample is to be described here.
Concept introduction:
One of the branches of materials science is known as thermal analysis. Determination properties of materials are done on the basis of change of temperature and it is known as thermal analysis. Many methods are there as example TGA or DSC etc.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Explain the principle of electrostatic precipitation in gas cleaning .
Differential Thermal Analysis (DTA) and Differential Scanning Calorimetry
(DSC) are used to support the information obtained from Thermogravimetric
Analysis (TGA) of polymers. Explain.
Volatile and semi-volatile compounds can be analyzed by GC
Chapter 31 Solutions
Principles of Instrumental Analysis
Knowledge Booster
Similar questions
- 5. In preparation for the analyses of other types of samples that may reach your laboratory, the supervisor tasked you to research different extraction procedures for the analyses of Tetrahydrocannabinol (THC) and other related compounds so that you can purchase different extraction instruments. How will you convince him to buy a Supercritical Fluid Extraction Instrument? Carrow_forwardThe researcher extracts a sample of well water and prepares it for TXRF analysis with a 10.00 mg/L V internal standard, like the calibration standards. The result produces SCa = 69297.81 and SV = 13481.2.Determine the concentration of Ca.arrow_forwardDiscuss the solubility behaviour of polymers from a thermodynamic point of view. What is the influence of the molecular weight on the solubility? Discuss the two main mechanisms of phase separation in a macromolecular solution. Give a connection to thermodynamics. Discuss in own words extended chain and end-to-end distance for a polymer.arrow_forward
- What is the negative skin friction in the context of pile behaviour? How and under what conditions does it occur? What is its significance in the design of pile foundations?.arrow_forwardshort, 1-minute survey. DISMISS 5. In the Dumas method for determining the molar mass of an unknown volatile liquid, a sample of a volatile liquid that boils below 100°C is vaporized in a boiling water bath and the mass of the vapor required to fill the flask is determined. The following data was collected: 4oFlask Volume 100.0 + 100.0 + 79.6 mL = 279.6 mL Mass of Flask + Cap Mass of Flask + Condensed Liquid Mass of Condensed Liquid Temperature of Water Bath (°C) Barometric Pressure (atm) 143.85 g 144.95 g 1.10 g 84.1 °C 0.985 atm a. What is the molar mass of the unknown? b. What will its temperature be when the pressure is 1.20 atm and the volume is 250.0 mL?arrow_forwardPart II: Kinetic Energy and Speed Sketch and compare the distributions for kinetic energy and speed at two different temperatures in the table below. Record your temperatures (T and 2 1 T ), set Volume as a Constant Parameter, and use roughly the same number of particles for each experiment (aim for ~100-200). Use the T temperature to examine a mixture of particles. T 1 2 = q, T₂ = □ KK Tips: The Species Information and Energy Histograms tools will 2 help. The system is dynamic so the distributions will fluctuate. Sketch the average or most common distribution that you see.arrow_forward
- (c) The data set below represents the surface tension data for aqueous solutions of 3- methylbutanoic acid [(CH3)2CHCH₂COOH] at 25°C. [C] [mol.dm³] 0 Y[mN.m'] 72.7 0.009 64.6 0.026 59.0 0.065 51.3 0.135 47.0 (i) Calculate the surface excess of 3-methylbutanoic acid (in mol.m2) and (ii) Hence estimate the molecular cross sectional area (in nm²) for this surface active molecule. (iii) Compare your estimate with the molecular cross sectional area one might expect for n-butanoic acid and account for the difference, if any, between the two surface active molecules.arrow_forwardInvestigate and explain two experimental methods to measure the molecular ` weight distribution of polymers.arrow_forwardUNIT 1. What is umnplung? Provide example.arrow_forward
- Describe the process of catalytic cracking used in petroleum refining industry.Your answer must include : (1) a balanced chemical equation inluding physical states and reaction conditions (2) example of a product formed from catalytic cracking in petroleum refining and its usearrow_forwardIn reference to surface chemistry, define dialysis.arrow_forwardfactors which would contribure to departure from Nernstian behaviour.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning