Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 24, Problem 14RQ
In a typical solid arbor milling cutter shown in Figure 24.10, why are the teeth staggered? (Review the discussion of dynamics in Chapter 21.)
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider a profile milling operation, where the
initial (stock) geometry has (X,Y,Z) dimensions of
100 mm x 75 mm x 50 mm. The target part has
dimensions of 95 mm x 70 mm x 50 mm. The
target part is located in the centre of the stock
part, i.e. the stock to be removed from all sides is
equal. The operation has a cutting time of 1
minute. The tool axis is along the Z direction and
the tool diameter is 12 mm having 6 cutting
edges. The takes place at 54m/min
feed rate of 0.2 mm/rev/tooth.
Calculate the axial depth of cut ?
process
at a
A single-point cutting tool with 12° rake angle is used to machine a steel work-piece. The depth of cut, i.e. uncut thickness is 0.81 mm. The chip thickness under orthogonal machining condition is 1.8 mm. What is the shear angle.
In 3-axis milling, the table feedrate is
703.00 mm/min. Using a 10mm
endmill to cut the material with a
radial depth of 4.60 mm and axial
depth of 4.20 mm, what is the
material removal rate (Cm³ /min) in
this operation?
Your Answer:
Answer
Chapter 24 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 24 - Suppose that you wanted to machine cast iron with...Ch. 24 - How is the feed per tooth related to the feed rate...Ch. 24 - Why must the number of teeth on the cutter be...Ch. 24 - Why is the question of up or down milling more...Ch. 24 - For producing flat surfaces in mass-production...Ch. 24 - Milling has a higher metal removal rate than...Ch. 24 - Which type of milling (up or down) is being done...Ch. 24 - Why does down milling dull the cutter more rapidly...Ch. 24 - What parameters do you need to specify in order to...Ch. 24 - In Figure 24.2b, the tool material is carbide....
Ch. 24 - What is the advantage of a helical-tooth cutter...Ch. 24 - What would the cutting force diagram for Fc look...Ch. 24 - Could the stub arbor-mounted face mill shown in...Ch. 24 - In a typical solid arbor milling cutter shown in...Ch. 24 - Make some sketches to show how you would you set...Ch. 24 - Make some sketches to show how you would set up a...Ch. 24 - Explain how controlled movements of the work m...Ch. 24 - Prob. 18RQCh. 24 - What is the purpose of the hole-circle plate on a...Ch. 24 - You have selected a feed per tooth and a cutting...Ch. 24 - How much time will be required for a milling...Ch. 24 - If the depth of cut is 0.35 in., what is the metal...Ch. 24 - Prob. 4PCh. 24 - Calculate the spindle rpm and table feed (ipm) for...Ch. 24 - A gray cast iron surface 6 in. wide and 18 in....Ch. 24 - Prob. 7PCh. 24 - In Figure 24.12, the feed is 0.006 in. per tooth....Ch. 24 - Suppose you want to do the job described in...Ch. 24 - The Bridgeport vertical-spindle milling machine is...Ch. 24 - The KC Machine Works, which does job shop...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The volumetric flow rate and discharge velocity of the air.
Introduction to Heat Transfer
Water flows from a larger pipe, diameter D1 = 100 mm, into a smaller one, diameter D2 = 50 mm, by way of a reen...
Fox and McDonald's Introduction to Fluid Mechanics
Assume that the air in Problem 3-22 is supplied to the space at 53 F (12 C). Compute the volume flow rate of th...
Heating Ventilating and Air Conditioning: Analysis and Design
The moments of inertia Iu,Iv and the product of inertia Iuv for the rectangular area.
Engineering Mechanics: Statics & Dynamics (14th Edition)
A 100-mm-long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is applied to it, determine the ch...
Mechanics of Materials
Consider refrigerant R-134a flowing in a smooth, horizontal, tube of wall thickness 2 mm. The refrigerant is at...
Fundamentals of Heat and Mass Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 450 mm long work piece is finished using a face milling cutter with a diameter of 75 mm. The overrun is 4 mm and the cutting depth of 3 mm. Calculate the total milling length.arrow_forwardDuring orthogonal cutting of MS with a 10 ° rake angle tool, the chip thickness ratio was obtained as 0.4. Calculate shear anglearrow_forwardProblem #2: Do a comparison between turning Vs. milling operations use some graphs if possible.arrow_forward
- What is the feed speed (mm/min) of an end milling cutter if it mills a distance of 300 mm in ten minutes? What is the feed per tooth if it is rotating at 800 rpm?arrow_forwardTurning Operation In a production turning operation, the foreman has decreed that a single pass must be completed on the cylindrical workpiece in 4.8 min. The piece is 400 mm long and 150 mm in diameter. Using a feed = 0.43 mm/rev and a depth of cut = 4.0 mm, what cutting speed must be used to meet this machining time requirement? Hint: Re-arrange the Tm equation to find v in m/min Tm= T.DO.L v.f 1.522arrow_forwardCalculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a feed rate of 0.004".arrow_forward
- across the surface and (b) the maximum metal removal rate during cutting A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in long by 2.5 in wide. The helical milling cutter, which has a 3.0 in diameter and ten teeth, is set up to overhang the width of the part on both sides. Cutting speed is 125 ft/min, feed is 0.006 in/tooth, and depth of cut = 0.300 in. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.5 in is provided at the beginning of the pass (before cutting begins), and an overtravel distance is provided at the end of the pass equal to the cutter radius plus 0.5 in, what is the duration of the feed motion.arrow_forwardd) A face milling operation is used to machine 6.0 mm from the top surface of a rectangular piece of aluminum 300 mm long by 125 mm wide in a single pass. The cutter has four teeth (cemented carbide inserts) and is 150 mm in diameter. The cutting speed = 2.8 m/s, and chipload = 0.27 mm/tooth. Assuming that the cutter enters the workpiece from its short side and follows a path that is centered over the workpiece, determine: i) the actual machining time to make the pass across the surface and, ii) the maximum metal removal rate during cutting.arrow_forwardA straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel rod. The feed is 0.2 mm/rev and the depth of cut is o.5 mm. The tool has a side cutting edge angle of 60°. The uncut chip thickness (in mm) is .. . ... ...arrow_forward
- Calculate the spindle speed (rpm) for turning operation when the cutting speed is 107.00 m/min and external diameter is D44.00 mm? (Two decimal places; Don't input units.) Your Answer: Answerarrow_forwardCalculate the machining time required for making 60 holes on an MS plate of 80 mm thickness with a drillbit of diameter 20 mm with a cutting speed V= 40 m/min, the feed f = 0.2 mm/rev. (Assume approach length,A and over run O as 2mm and point angle as 110o). Calculate material removal rate.arrow_forward17) A50-mm-dia endmill cuts 6061 aluminum with 30% tool engagement at a depth of 6 mm. The tool rotates at 200 rpm and is feeding at 250 mm/min. There are 2 teeth set at a rake angle of 10°. a. Calculate the required power of cutting. b. Determine the spindle torque. c. Determine the cutting force on each tooth. d. If the thrust force is measured to be 350N, estimate the tool-chip interface friction coefficient. How could you physically verify your power estimate?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Polymer Basics; Author: Tonya Coffey;https://www.youtube.com/watch?v=c5gFHpWvDXk;License: Standard youtube license