Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 24, Problem 7P
To determine
The break even quantity below which the shaper machine is more economical than milling.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A milling cutter having 8 teeth is rotating at 150
rpm. If the feed per tooth is 0.1 mm, the speed
in mm per minute is
A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the workpiece.
A facing operation is performed on an lathe. The diameter of the cylindrical part is 6 in and the length is
15 in The spindle rotates at 180 rpm. Use depth of cut of 0.110 in and feed of 0.008 in rev. Determine:
a) The cutting speed of the tool (in/min)
b) The tool feed rate (in min)
c) The cutting time (sec)
Chapter 24 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 24 - Suppose that you wanted to machine cast iron with...Ch. 24 - How is the feed per tooth related to the feed rate...Ch. 24 - Why must the number of teeth on the cutter be...Ch. 24 - Why is the question of up or down milling more...Ch. 24 - For producing flat surfaces in mass-production...Ch. 24 - Milling has a higher metal removal rate than...Ch. 24 - Which type of milling (up or down) is being done...Ch. 24 - Why does down milling dull the cutter more rapidly...Ch. 24 - What parameters do you need to specify in order to...Ch. 24 - In Figure 24.2b, the tool material is carbide....
Ch. 24 - What is the advantage of a helical-tooth cutter...Ch. 24 - What would the cutting force diagram for Fc look...Ch. 24 - Could the stub arbor-mounted face mill shown in...Ch. 24 - In a typical solid arbor milling cutter shown in...Ch. 24 - Make some sketches to show how you would you set...Ch. 24 - Make some sketches to show how you would set up a...Ch. 24 - Explain how controlled movements of the work m...Ch. 24 - Prob. 18RQCh. 24 - What is the purpose of the hole-circle plate on a...Ch. 24 - You have selected a feed per tooth and a cutting...Ch. 24 - How much time will be required for a milling...Ch. 24 - If the depth of cut is 0.35 in., what is the metal...Ch. 24 - Prob. 4PCh. 24 - Calculate the spindle rpm and table feed (ipm) for...Ch. 24 - A gray cast iron surface 6 in. wide and 18 in....Ch. 24 - Prob. 7PCh. 24 - In Figure 24.12, the feed is 0.006 in. per tooth....Ch. 24 - Suppose you want to do the job described in...Ch. 24 - The Bridgeport vertical-spindle milling machine is...Ch. 24 - The KC Machine Works, which does job shop...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. In Figure 1, the feed is 0.006 in. per tooth. The cutter is rotating at an rpm that will produce the desired surface cutting speed of 125 fpm. The cutter diameter is 3 in. The depth of cut is 0.15 in and width of the cut is 2 in. The block is 5 in. wide and 12in long. Determine a. The feed, in inches per minute. b. Approach distance for this type of milling c. Cutting time to make one pass across the surface d. If an additional approach distance of 0.5 in is provided at the beginning of pass and an over travel distance is provided at the end of pass equal to the cutter radius plus 0.5 in, what is the duration of the feed motion? Speesi neten Cite Citter praiten t staof cit Solld hellcal plain milling cuttar Wout Helical teeth TUp w Figure: 01arrow_forward2. Enumerate the different machine elements can be seen in the figure below.arrow_forwardBriefly describe the process of locating the center of an existing hole on a vertical milling machine.arrow_forward
- In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm respectively, And the driver pulley runs at speed of 225 rpm. Find the speed at which is driven pulley runs in the machine. the speed of the driven pulley in rpm isarrow_forward2. Write a complete program to mill around the part. The endmill is .500 diameter, and you want to leave .010 stock for a finish pass. Enter a diameter offset number (Dn) command for tool DIAMETER Geometry of .520 for machining a roughing pass around part. And then define another pass around part using the same program coordinates but a different diameter offset number (Dn), and enter in the correct diameter offset value of .500 to machine part to the finish size. TOOL 1 has 0.520 in D21 and 0.500 in D01 Tool Speed (rpm) Feed (ipm) Operation Finish outside contour, x .50 deep Tooling 1 .5D endmill 1200 6. 25 R.25 2 PL. R .50 2.00 XO YO 4.0 SO. 1.0 SQ. 5 DA. EM 1.250- X-2.5 Y-2.0 START POINTarrow_forwardA two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is 1.0 inches thick. Both drills have point angles of 118 degrees and the cutting speed for the material is 300 ft/min. The rotational speed of each drill can be set individually but the feed rate for both holes must be set to the same value because they move together into the material. The feed rate is set so that the total metal removal rate of both drills combined does not exceed 1.50 in3/min. Determine (a) maximum feed rate (in/min) that can be used, (b) individual feeds (in/rev) for each hole, and (c) cutting time for the operation.arrow_forward
- Match column A with Column B (Return this page with your answer sheet) No Column A These are machine tools in which components are Column B No Multi-Spindle A machined. Automatics Several tools are used so that the turning is Broaching B completed in one cycle. 3 Designed for high production rate machining of screws and similar threaded parts, Job Production 4 These lathes have four to eight spindles arranged Flow Production in a circle on a large drum. This operation is like shaping with multiple teeth E Batch Production and is used to machine internal and external surfaces such as holes of circular. 6 The workpiece is supported on its OD and rotated F Auto Lathe around an axis created by this reference surface. The workpiece is free to shift, and if the support surface is the one being ground, the axis of rotation also shifts. Manufacturing of single, or few products to a Electrical copying System G customer's individual specification. 8 Parts are manufactured in fixed quantities H…arrow_forward1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material? 4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be used if a 15 mm high speed steel drill is used to cut brass workpiece? 5. A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not, then what must be the correct rpm setting considering that the machine has the following rpm settings of 300, 600, 900, 1200, and 1800?arrow_forwardoperation, the shear IS cIose to, In turning operation, spindle speed is set to provide a cutting speed of 2.2 m/: The feed and depth of cut are 0.32 mm and 2.1 mm, respectively. The tool rake angle is 15°. After the cut, the deformed chip thickness is measured to be 0.43 mm. Using the Orthogonal model as an approximation of turning operation, the shear strain is close to, In turning operation, spindle speed is set to provide a cutting speed of 2.4 m/arrow_forward
- Q.B5. a.) In a drilling operation, 3 blind holes needs to be drilled to a depth of 16 mm and a diameter of 8 mm. The point angle is 105° and the drill is made from HSS material. The bench drill allows a fixed speed of 1400 RPM and a feed of 0.1 mm per rev. The work part is mild steel with a thickness of 22 mm. Determine the time required to complete this operation. b.) What are some factors that determine the type of industrial cleaning that will be applied to a part? c.) In mass finishing, two key processes have been discussed - state both the processes here and explain their difference. d.) Draw and explain how a basic heading operation is carried out to produce nails.arrow_forwardIn a turning process using orthogonal tool geometry, a chip length of 100 mm is obtained for an uncut chip length of 250 mm. The cutting conditions are cutting speed 30 m/min, rake angle = 20°º. The shear plane angle is degrees (round off to one decimal place). =arrow_forward2.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght of the work piece is 200mm. The feed is 0.2 mm/rev. Ignoring approach and overtravel, the machining time for one pass will be nearest to (min).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License