Physics for Scientists and Engineers
6th Edition
ISBN: 9781429281843
Author: Tipler
Publisher: MAC HIGHER
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 25, Problem 34P
(a)
To determine
The number density of protons.
(b)
To determine
The number of protons strike the target per minute.
(c)
To determine
The magnitude of current density.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An accelerator produces a beam of protons with a circular cross section that is 2.3 mm in diameter and has a current of
0.8 mA. The current density is uniformly distributed throughout the beam. The kinetic energy of each proton is 20 MeV.
The beam strikes a metal target and is absorbed by the target.
1) What is the number density of the protons in the beam?
n-3
m Submit
You currently have 0 submissions for this question. Only 10 submission are allowed.
You can make 10 more submissions for this question.
2) How many protons strike the target in each minute?
Submit
You currently have 1 submissions for this question. Only 10 submission are allowed.
You can make 9 more submissions for this question.
3) What is the magnitude of the current density in this beam?
kA/m² Submit
You currently have 1 submissions for this question. Only 10 submission are allowed.
You can make 9 more submissions for this question.
An accelerator produces a beam of protons with a circular cross section that is 2.0 mm in diameter and has a current of 1.0 mA. The current density is uniformly distributed
throughout the beam. The kinetic energy of each proton is 20 MeV. The beam strikes a metal target and is absorbed by the target.
(a) What is the number density of the protons in the beam?
m-3
(b) How many protons strike the target in each minute?
(c) What is the magnitude of the current density in this beam?
KA/m2
A 5.00A Current runs through a 12-guage copper wire (diameter 2.05mm) and through a light bulb. Copper has 8.5 x 10^28 free electrons per cubic meter. (a) How many electrons pass through the light bulb each second? (b) What is the current density of the wire? (c) At what speed does a typical electron pass by any given point in the wire? (d) If you were to use wire of twice the diameter which of the above answer would change? Would they increase or decrease? Tip. Area for circle and velocity from J formula.
Chapter 25 Solutions
Physics for Scientists and Engineers
Ch. 25 - Prob. 1PCh. 25 - Prob. 2PCh. 25 - Prob. 3PCh. 25 - Prob. 4PCh. 25 - Prob. 5PCh. 25 - Prob. 6PCh. 25 - Prob. 7PCh. 25 - Prob. 8PCh. 25 - Prob. 9PCh. 25 - Prob. 10P
Ch. 25 - Prob. 11PCh. 25 - Prob. 12PCh. 25 - Prob. 13PCh. 25 - Prob. 14PCh. 25 - Prob. 15PCh. 25 - Prob. 16PCh. 25 - Prob. 17PCh. 25 - Prob. 18PCh. 25 - Prob. 19PCh. 25 - Prob. 20PCh. 25 - Prob. 21PCh. 25 - Prob. 22PCh. 25 - Prob. 23PCh. 25 - Prob. 24PCh. 25 - Prob. 25PCh. 25 - Prob. 26PCh. 25 - Prob. 27PCh. 25 - Prob. 28PCh. 25 - Prob. 29PCh. 25 - Prob. 30PCh. 25 - Prob. 31PCh. 25 - Prob. 32PCh. 25 - Prob. 33PCh. 25 - Prob. 34PCh. 25 - Prob. 35PCh. 25 - Prob. 36PCh. 25 - Prob. 37PCh. 25 - Prob. 38PCh. 25 - Prob. 39PCh. 25 - Prob. 40PCh. 25 - Prob. 41PCh. 25 - Prob. 42PCh. 25 - Prob. 43PCh. 25 - Prob. 44PCh. 25 - Prob. 45PCh. 25 - Prob. 46PCh. 25 - Prob. 47PCh. 25 - Prob. 48PCh. 25 - Prob. 49PCh. 25 - Prob. 50PCh. 25 - Prob. 51PCh. 25 - Prob. 52PCh. 25 - Prob. 53PCh. 25 - Prob. 54PCh. 25 - Prob. 55PCh. 25 - Prob. 56PCh. 25 - Prob. 57PCh. 25 - Prob. 58PCh. 25 - Prob. 59PCh. 25 - Prob. 60PCh. 25 - Prob. 61PCh. 25 - Prob. 62PCh. 25 - Prob. 63PCh. 25 - Prob. 64PCh. 25 - Prob. 65PCh. 25 - Prob. 66PCh. 25 - Prob. 67PCh. 25 - Prob. 68PCh. 25 - Prob. 69PCh. 25 - Prob. 70PCh. 25 - Prob. 71PCh. 25 - Prob. 72PCh. 25 - Prob. 73PCh. 25 - Prob. 74PCh. 25 - Prob. 75PCh. 25 - Prob. 76PCh. 25 - Prob. 77PCh. 25 - Prob. 78PCh. 25 - Prob. 79PCh. 25 - Prob. 80PCh. 25 - Prob. 81PCh. 25 - Prob. 82PCh. 25 - Prob. 83PCh. 25 - Prob. 84PCh. 25 - Prob. 85PCh. 25 - Prob. 86PCh. 25 - Prob. 87PCh. 25 - Prob. 88PCh. 25 - Prob. 89PCh. 25 - Prob. 90PCh. 25 - Prob. 91PCh. 25 - Prob. 92PCh. 25 - Prob. 93PCh. 25 - Prob. 94PCh. 25 - Prob. 95PCh. 25 - Prob. 96PCh. 25 - Prob. 97PCh. 25 - Prob. 98PCh. 25 - Prob. 99PCh. 25 - Prob. 100PCh. 25 - Prob. 101PCh. 25 - Prob. 102PCh. 25 - Prob. 103PCh. 25 - Prob. 104PCh. 25 - Prob. 105PCh. 25 - Prob. 106PCh. 25 - Prob. 107PCh. 25 - Prob. 108PCh. 25 - Prob. 109PCh. 25 - Prob. 110PCh. 25 - Prob. 111PCh. 25 - Prob. 112PCh. 25 - Prob. 113PCh. 25 - Prob. 114PCh. 25 - Prob. 115PCh. 25 - Prob. 116PCh. 25 - Prob. 117PCh. 25 - Prob. 118PCh. 25 - Prob. 119PCh. 25 - Prob. 120P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Taking R = 1.00 k and = 250 V in Figure P21.49, determine the direction and magnitude of the current in the horizontal wire between a and e. Figure P21.49arrow_forwardIf the current carried by a conductor is doubled, what happens to (a) the charge carrier density, (b) the current density, (c) the electron drift velocity, and (d) the average time interval between collisions?arrow_forwardAn aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the absolute value of the charge density in the wire? (b) What is the drift velocity of the electrons? (c) What would be the drift velocity if the same gauge copper were used instead of aluminum? The density of copper is 8.96 g/cm3 and thedensity of aluminum is 2.70 g/cm3. The molar mass ofaluminum is 26.98 g/mol and the molar mass of copper is 63.5 g/mol. Assume each atom of metal contributes one free electron.arrow_forward
- The current of an electron beam has a measured current of I=39.2 μA with a radius of 1.74 mm. What is the magnitude of the current density of the beam? Include units in your answer.arrow_forwardConsider a steady beam of protons. Each proton has kinetic energy 20 MeV. The beam represents a current of 0.25 μA. a) What is the potential difference through which the protons are accelerated? b) If the beam is directed perpendicular to a flat surface, how many protons strike the surface in 3 seconds?arrow_forward28 1 6.0 x 10 m3 1. Consider a cylindrical wire that has conduction electron density and radius 0.5 mm. An electric field with strength 7.5 x 10-4 creates a current of 4.8 x 10 electrons per second. a) What is the average drift speed for an electron? (include units) b) What is the average time in between electron collisions? fs (express your answer in femtoseconds)arrow_forward
- A 5.00 A current runs through a 12 gauge copper wire (diameter 2.05 mm) and through a light bulb. Copper has 8.5 * 1028 free electrons per cubic meter. (a) How many electrons pass through the light bulb each second? (b) What is the current density in the wire? (c) At what speed does a typical electron pass by any given point in the wire? (d) If you were to use wire of twice the diameter, which of the above answers would change? Would they increase or decrease?arrow_forwardIn proton beam therapy, a beam of high-energy protons is used to kill cancerous cells in a tumor. In one system, the beam, which consists of protons with an energy of 2.8 x 10-11 J, has a current of 80 nA. The protons in the beam mostly come to rest within the tumor. The radiologist has ordered a total dose corresponding to 3.6 x 10-3 J of energy to be deposited in the tumor.a. How many protons strike the tumor each second?b. How long should the beam be on in order to deliver the required dose?arrow_forwardA 5.00A Current runs through a 12-guage copper wire (diameter 2.05mm) and through a light bulb. Copper has 8.5 x 10^28 free electrons per cubic meter. (a) How many electrons pass through the light bulb each second? (b) What is the current density of the wire? (c) At what speed does a typical electron pass by any given point in the wire?arrow_forward
- A fuse in an electric circuit is a wire that is designed to melt, and thereby open the circuit, if the current exceeds a predetermined value. Suppose that the material to be used in a fuse melts when the current density rises to 440 A/cm2. What diameter of cylindrical wire should be used to make a fuse that will limit the current to 0.50 A?arrow_forwardA fuse in an electric circuit is a wire that is designed to melt, and thereby open the circuit, if the current exceeds a predetermined value. Suppose that the material to be used in a fuse melts when the current density rises to 440 A/cm?. What diameter of cylindrical wire should be used to make a fuse that will limit the current to 0.50 A?arrow_forwardA heart defibrillator is used to enable the heart to start beating if it has stopped. This is done by passing a large current of 1 A through the body at 10 V for a very short time, usually about 6 ms. How much energy is transferred in mJ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Circuits, Voltage, Resistance, Current - Physics 101 / AP Physics Review with Dianna Cowern; Author: Physics Girl;https://www.youtube.com/watch?v=q8X2gcPVwO0;License: Standard YouTube License, CC-BY