Industrial Motor Control
7th Edition
ISBN: 9781133691808
Author: Stephen Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 50, Problem 8RQ
When using a two-input NAND gate, what condition of input must be met to have an output?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
qq5
Which of the following gate will have high output if at least any one input is high ?.
a.
NAND Gate
b.
NOR Gate
c.
AND Gate
d.
OR Gate
. the
(b) A block diagram for arc welding process control in depicted as in Figure
controller regulates the arc current, which results changes in the wire-melting process
if error occurred. Determine the transfer function of this closed loop system.
Controller
Wire-melting process
Are
Desired
Error
K
$ + 2
current
Puddle
diameter
(0.5s + 1)(s + 1)
diameter
Measured
Vision system
diameter
0.005s + 1
Figure
need in s domain
Chapter 50 Solutions
Industrial Motor Control
Ch. 50 - Prob. 1RQCh. 50 - What precautions must be taken when connecting...Ch. 50 - What do the letters COSMOS stand for?
Ch. 50 - When using a two-input AND gate, what conditions...Ch. 50 - When using a two-input OR gate, what conditions of...Ch. 50 - Explain the difference between an OR gate and an...Ch. 50 - When using a two-input NOR gate, what condition of...Ch. 50 - When using a two-input NAND gate, what condition...Ch. 50 - If an INVERTER is connected to the output of a...Ch. 50 - If an INVERTER is connected to the output of an OR...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- when i input 0 for x=0 and y=0, it does c2 does not equal zero. is there a reason why it is zero?arrow_forwardQ: Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Feed Reactor temperature set point (master) TC Water surge tank i Jacket itemperature i set point (slave) TC LC-LT Reactor Cooling water out Product Cooling water makeup Circulation pump Figure (2)arrow_forwardYou are tasked to enhance the performance of an analog plant using a digital controller PID. The controller is in connected in series with the plant in a closed-loop configuration. The pulse transfer K(z+a) function is given as GzohGp(s) =- Use sampling time Ts=0.6 second, K=8, a=0.78, b=-0.602 (0+z)(q+z) and c=-0.705. Do the following: i. Obtain the design point in z-coordinates to achieve the requirement of having a system settling time of 3 second, and damping ratio of zeta (z=0.705).arrow_forward
- öalg äbäi The closed-loop system transfer function of a control system is given by the following figure, for unit step input what is the * ?output 2(s – 2) R(s) (s +2)(s + 1) c(s) | %D a- -1+e-2t – e-t b- -1 – e-2t + e-t c- -1 + 4e-2t – 3e-t d- -1 – 4e-2t + 3e¬t a darrow_forwardIdentify the following elements of the given closed loop control system.(i) Process Element(ii) Feedback Element (iii) Control Element (iv) Correction Elementarrow_forward1.Design a sequential circuit with two D Flip-Flops, A and B, and one input x. When x = 0, then the state of thecircuit remains the same. When x =1, the circuit goes through the state transitions from 00 to 01 to 11 to 10back to 00, and repeats.arrow_forward
- The delay in the response of any feedback system is called as system lag. Select one: O True O Falsearrow_forwardThe system will have a direct connection between the output and input.arrow_forwardWrite an AVR program using the timer to generate a square wave at a frequency of 50KHz knowing that the main frequency of the microcontroller XTAL is 5MHzarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License