When force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the normal strain developed in wire CD: Calculate your answer to 4 digit place. -400 mm D 200 mm 300 mm B mm/mm.
Q: 3 in. y 3 in. i ↓ 4 in. - 5 in. X y 0 50 -30- 40 15 Dimensions in mm X
A:
Q: Find the angular velocity of the gear and the velocity of A at the instant shown. 2 ft/s www vvvwvww…
A: VA=Rω for pure rolling condition ω=VAR =20.75=2.667 rad/s
Q: Material P is suggested to be used as a rod with the applied stress up to 300 Material P has a yield…
A:
Q: QUESTION 1 A manufacturer conducted an experiment for an evaporator capacity 533 kW cooling and…
A: Given: Capacity of evaporator: →QE=533 KW COP of the absorption refrigeration system: →COP=1.8…
Q: The block C is moving downwards at the speed shown. Find the speed of B and the angular velocity of…
A:
Q: Water at 20°C flows with a steady mean velocity of 2.0 m/s through a $100mm pipe that slopes upward…
A:
Q: An infinite steel plate, 30 mm thick, is subjected to a tensile stress. It contains a through…
A: Given KIC = 80 MPa m-1/2 ; yield stress (Sy) = 1000 MPa Assume Y = 1 for an infinite plate. (a)…
Q: C 30° 3 m 4 m B 98 200 N/m 100 N
A: Given,
Q: The 30-N force causes the bar to tip = 13° when the force is applied. Originally the bar is…
A: Given data force at C =30N Angle = 13° Find the stiffness of each spring.
Q: Refrigerant 134a enters a well-insulated nozzle at 200 lbf/in.2, 170°F, with a velocity of 120 ft/s…
A:
Q: A 0.78 m³ tank initially contains water at 260°C and a quality of 0.81. A valve at the top of the…
A: Given Data: The initial volume of water in the tank V1=0.78 m3 The temperature throughout the…
Q: 20 R30 Ø30 30 Ø30 TOP VIEW 25 FRONT VIEW 30 R30 20
A: Given: Front view and top view to draw isometric view of an object.
Q: 8-Consider a 0.8 m high and 1.5-m-wide double-pane window consisting of two 4-mm-thick layers of…
A:
Q: What is production engineering?
A: Given Data- Topic production engg given We have to explain it.
Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…
A:
Q: Where do i put FA and FB. my answer was wrong
A: To find: Free body diagram of the beam. A free body diagram indicates all the moments, forces…
Q: A gasoline pump fills an 80 L tank in 1 min 15 second. If the pump exit diameter is 4 cm, what is…
A: Option A is correct.
Q: A long ladder 20 feet long is leaning against a wall with one end on the floor. The bottom end of…
A:
Q: For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine…
A: Given data: W=7000 lbTAB=13000 lbd=1 in Need to determine the shear stress in the 1 inch diameter…
Q: In a cogeneration system, a Rankine cycle operates with steam entering the turbine at 800 lb/in.2,…
A:
Q: In the clevis shown in Fig. 1-11b, find the minimum bolt diameter and the minimum thickness of each…
A: Given data as per questionLoad, P=63 kNAllowable Shearing stress, τ=38 MPaAllowable Bearing stress,…
Q: An ideal otto cycle has a compression ratio of 8(10.8). At the beginning of the Compression process,…
A:
Q: A sport car is traveling along a 12° banked road having a radius of curvature of 149 ft. The driver…
A: Given: angle = 12 deg radius R = 149 ft Velocity v = 79 ft/s To find: friction coefficient
Q: Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.² and…
A: Given data: steam exits the steam generators P5=1500 lbf/in2 and T5= 1100°FThe pressure and…
Q: 7- Illustrates a composite wall. The wall is composed of two materials (A with kA = 1 W/m-K and B…
A:
Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lbf/in² and…
A:
Q: Determine the components of the hinge forces at A and F. Show your complete solution
A: Draw the free-body diagram of whole system.
Q: Consider a Venturi with a throat-to-inlet area ratio of 0.8 mounted in a flow at standard sea level…
A: Given data: Throat to inlet diameter ratio=0.8∆P=335 Pa Need to determine the velocity of the flow…
Q: Prepare 2-3 Pages slide on Properties of ceramics and classifications. you can attach in image…
A:
Q: ate analysis a co a heating 12,000 %0C, .4.65%H, Nitrogen 1.24%, Sulfur 3.50%, Oxygen 8.14%, and Ash…
A: Let fuel formula, CxHySzOwNv and the resulting product information.x = wt%C/12.0107 =…
Q: A manufacturer conducted an experiment for an evaporator capacity 500 kW cooling and designed for…
A: Given data: evapotator capacity is 500KWCOP is 2The evaporator operates 20°CThe condenser operates…
Q: 1. Determine the minimum coefficient of static friction us which will allow the drum with fixed…
A:
Q: A 300 200 N 200 N су D 500 N 200 N E 225 300 Dimensions in mm 225 B
A: Given Data- A cantilever beam given we have to draw SFD BMD and find maximum value of shear force…
Q: The magnitude of the force F is 0.2 N and its direction cosines are cos0x = 0.727, cosey: 0.582.…
A:
Q: In the figure below, a member is subjected to an axial force P. If the cross sectional area of the…
A:
Q: A load of 3500 N is applied to a titanium wire with a diameter of 0.30 cm. Compute to find out…
A: Given : load , F = 3500 N diameter of wire. d =0.30 cm = 3 mm yield strength of the wire , σY = 305…
Q: Com Posit Wall K₁=20₂ K₂=30₂ K3=40 w/mc at Steries repectively Thickness for at three layer are…
A:
Q: A cylindrical bucket 30 cm in diameter and 50 cm high weighing 25 N contains oil (SG = 0.80) to (a)…
A: Given data as per question Diameter of cylindrical bucket, D=30 cm=0.3 m Height of cylindrical…
Q: Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater. Steam…
A:
Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and…
A:
Q: Determine all the internal members of the truss shown. Indicate if its compression or tension. JOEN
A:
Q: Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater.…
A:
Q: Find the sum of the vertical forces in pounds if F1 = 30 lb at 60 deg N of W and 50 lb at 40 deg S…
A:
Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…
A:
Q: Water is being pumped from a lower reservoir to an upper reservoir 45 m above rate of 30 litres per…
A: GivenH=45mQ=30 ltr/s=0.030 m3/sPs=24 kWhL=8mρ=1000 kg/m3g=9.81 m/s2
Q: A cylinder of mass 100 kg is in contact with the smooth surfaces at And B and in static equilibrium…
A:
Q: 1. Pressure of a certain gas can be described by P = 8.314T V If the volume goes from 20L to 20.2L…
A:
Q: Consider an air standard Diesel cycle. At the beginning of compression, the temperature is 300 K and…
A: Given:At the beginning of compression, P1=101.35 kPa, T1=300 KCompression ratio, r=15Heat added in…
Q: 5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k =…
A:
Q: Group Problem: You are planning to build a log cabin in Northern Minnesota on a remote hill with a…
A: Write the given data. mlog=1000 lbsamax=3 ft/s2μ=0.5θ=20°
When force P is apliced to the rigid arm BC, point B moves downward 0.2mm.
Determine the normal strain developed in wire CD: ___ mm/mm.
Calculate your answer to 4 digit place.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.A uniaxial force was applied on the shown coupon during an experiment. The thickness, width and length of the coupon are 1mm, 20mm and 100 mm, respectively. the force applied had a magnitude of 1000N. A strain rosette was applied to the sample as shown. Strain gages a and c are perpendicular to each other. On the other hand, the angle between strain gages b and a is 30°. The strain gages reported the following strains Ea = -0.2x10-3 Ep = 0.667x10-3 Determine the elastic properties of the isotropic coupon. 30 aA material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
- An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cmQ4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Eb = 60 µ and Ec = 20 u . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. 45 PumpThe strain components, ex= 940 micro strain, ey= -360 micro strain and yxy=830micro strain are given for a point in body subjected to plane strain. Determine; a. Magnitude of the principal strains b. The direction of the principal strain axes c. The maximum in-plane shear strain. Confirm your answer by means of Mohr's circle of strain and determine the linear strain on an axis inclined at 20 degrees clockwise to the direction of ey
- 1-A round member having a diameter of 3cm experience an axial load of 10KN. Two strain gauges are mounted on the member, one measuring an axial strain of 600 micro-strain and the other measuring a lateral strain of -163 micro-strain. The modulus of elasticity in GPa is Choose... The Poisson ratio is Choose... + The stress in MPa is Choose... + Next pageA 45° strain rosette was placed on the surface of a critical point on an engineering part. The following were measured: Ea = 400 μ C ли 45° mm mm 45° ли Gauge a was aligned with the x-axis. a. Determine Ex, Ey, Yxy b. Using Mohr's Circle, find the principal strains and the maximum shear strain at that point, and find the orientation of the principal planes from the given x-y axes. y ли & = 450 μ ஆ b a mm X mm & c = 500 μ y+ ос mm mm eb 10₂ XThe strain rosette shown in figure was used to obtain strain data at a point on the surface of a machine part. If the readings from gages a, b, c were 650, -450, -585 (all in microns) respectively; which of the following is the shear strain on the surface? 45° a Lutfen birini seçin a1370 micron b. 1570 micron c1400 micron d7600 micron
- Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.For the given state of plane strain, use Mohr's circle to determine the state of plane strain associated with axes x' and y rotated through the given angle 8. Ex=-500μ, &y=+250µ, Yxy = 0, 0 = 13° O (Round the final answers to one decimal place.) The strains are Ex'= Ey₁ = | Vx'y¹=[ HThree readings are obtained from an equiangular strain gage rosette mounted on a free and unloaded surface of a part. Determine the magnitude of the principal strains and their orientation with respect to the 0° gage. Check the results with a Mohr circle.Assume The three known strains are all linear strains