You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?

You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.23P

See similar textbooks

Similar questions

You are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…
O A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h - ft2 .°F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant Chip If the coolant is air and the corresponding convection coefficient is h = 200 W/m² · K, what is the maximum allowable chip power? If the coolant is a dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?
Furnace walls are lined by 3 layers: firebrick with a thickness of 6 in (k=0.95 Btu/h.ft. F), insulating brick (k-0.4 Btu/h.ft.°F) and common brick (k=0.8 Btu /h.ft.°F) Firebrick inlet temperature, T₁ = 1800°F, maximum insulating brick temperature, T₂ = 1720°F and T3 = 280°F. 1. Calculate the thickness of the insulating brick layer. 2. If the common brick is 9 in, calculate the exit temperature.
1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at To = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant T, h Chip = 200 W/m2 · K, what is the maximum allowable chip power? If the coolant is a If the coolant is air and the corresponding convection coefficient is h dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?
S is 6. A spherical shaped vessel of 1.4 m outer diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C. Thermal conductivity of the material of the sphere is 0.083 W/mK. (a) 0.2 kW (c) 1.088 kW (b) 0.5 kW (d) 1.6 kW
Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential energy lost in the drop could be converted to thermal energy used to heat the copper from an initial temperature of 25 degrees celsius, what would the final temperature of the copper wafer? Would the answer be different if the wafer has a mass greater than 3 grams? Note: the specific heat of copper is 387 J/(kg*K). The temperature is between 25.8 and 26.0 degrees celsius, yes the bigger the mass the greater the energy. O The temperature is between 25.6 and 25.8 celsius, answer does not depend on mass. O The temperature is between 25.0 and 25.2 celsius, answer does not depend on mass. O The temperature is 25.5 and of course the more mass something has the greater energy will be needed to raise the temperature. The temperature is 26.2 and if the mass is doubled so will be the change in temperature. O The temperature is 25.9 degrees celsius and the answer does not depend on mass. O The…
Air surrounding a light bulb is moving at 25 m/sec. The surrounding conditions are kept at atmospheric pressure and at temperature 25o C. The light bulb external surface is kept at 140o C. What is the heat transfer rate from the light bulb to the surrounding? Assume the light bulb as a sphere with a diameter of 50 mm.
Q2/ An aluminum sphere weighting 7kg and initially at a temperature of 533K is suddenly immersed in a fluid at 283K. if heat transfer coefficient between the sphere and fluid is 50W/m?.°C. Take density=2707kg/m3, specific heat=0.9KJ/kg.°C and thermal conductivity= 204W/m °C. إجابت * Determine the Bi number 0.00696 0.000696 0.0052 0.00052 0 أخری *.Determine the time required to cool sphere to 263K 26.28min 262.8min 52.56 min 525.6 min O أخری
A composite plane wall consisting of materials, 1.5-in steel (k = 312 BTU-in/HR.ft2.0F) and 2-in aluminum (k = 1400 BTU-in/HR.ft2.0F), separates a hot gas at Ti = 2000F, hi = 2 BTU/HR.ft2.0F, from cold gas at To = 80 deg F, ho = 5. If the hot fluid is on the aluminum side, find: a) Transmittance, U; b) The heat through 100 sq. ft of the surface under steady state condition and c) The interface temperature at the junction of the metals.
1. A beverage cooler is in the shape of a cube, 42 cm on each inside edge. Its 3.0-cm thick wall are made up of plastic (kr = 0.050 W/mK). When the outside temperature is 20°C, how much ice will melt each hour? Tice is 0°C. 2. One of the possible mechanisms of heat transfer in human body is conduction through body fat. Suppose that heat travels through 0.03 m of fat in reaching the skin, which has a total surface area of 1.7 m² and a temperature of 34°C. Find the amount of heat that reaches the skin in half an hour, if the temperature at the body, interior is maintained at the normal value 37°C ? Thermal conductivity of body fat is k = 0.2 J/sm°C. 3. The air in a room is at 25°C and outside temperature is 0°C. The window of the room has an area of 2m² and thickness 2mm. Calculate the rate of loss of heat by conduction through window ? Thermal conductivity for glass is 1 Wm¯'degree!.
Calculate the over-all coefficient of heat transfer U for a piece of glass1/8-in thick, exposed to still air at 70 °F on one side and 0 °F air moving at15 mph on the other side.