Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 73P
To determine
The static factor of safety.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
4. A solid square rod is cantilevered at one end. The rod is 0.6 m long and
supports a completely reversing transverse load at the other end of ±2 kN. The
material is AISI 1080 hot-rolled steel. If the rod must support this load for 104
cycles with a design factor of 1.5, what dimension should the square cross
section have? Neglect any stress concentrations at the support end.
65
Required information
A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load
at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles
with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the
support end.
Determine the endurance limit for this application. Assume that the size modification factor kis 0.85 until a size for the section is
known.
The endurance limit is 278.4 MPa.
The figure shows a connection that employs three SAE grade 4 bolts. The tensile shear load on the joint is
4000 lbf. The members are bars of AISI 1020 HR steel. Assume the bolt threads do not extend into the joint.
Find the factor of safety for each possible mode of failure. (Refer example problem 8.6 on pg. 445).
in ∞
in 100
in
1 in
in
Đ
1in
-2 in
in-20 UNC
5
5
in
in
Chapter 8 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 8 - A power screw is 25 mm in diameter and has a...Ch. 8 - Using the information in the footnote of Table...Ch. 8 - Show that for zero collar friction the efficiency...Ch. 8 - A single-threaded power screw is 25 mm in diameter...Ch. 8 - The machine shown in the figure can be used for a...Ch. 8 - The press shown for Prob. 8-5 has a rated load of...Ch. 8 - For the screw clamp shown, a force is applied at...Ch. 8 - The C clamp shown in the figure for Prob. 8-7 uses...Ch. 8 - Find the power required to drive a 1.5-in power...Ch. 8 - A single square-thread power screw has an input...
Ch. 8 - Prob. 11PCh. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - Prob. 13PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Repeat Prob. 8-14 with the addition of one 12 N...Ch. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Two identical aluminum plates are each 2 in thick,...Ch. 8 - Prob. 18PCh. 8 - A 30-mm thick AISI 1020 steel plate is sandwiched...Ch. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - An aluminum bracket with a 12-in thick flange is...Ch. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - A 34 in-16 UNF series SAE grade 5 bolt has a 34-in...Ch. 8 - From your experience with Prob. 8-26, generalize...Ch. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - For a bolted assembly with eight bolts, the...Ch. 8 - Prob. 32PCh. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - 837 to 840 Repeat the requirements for the problem...Ch. 8 - Prob. 40PCh. 8 - 841 to 844 For the pressure vessel defined in the...Ch. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Bolts distributed about a bolt circle are often...Ch. 8 - The figure shows a cast-iron bearing block that is...Ch. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - Prob. 52PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - For the pressure cylinder defined in the problem...Ch. 8 - A 1-in-diameter hot-rolled AISI 1144 steel rod is...Ch. 8 - The section of the sealed joint shown in the...Ch. 8 - Prob. 61PCh. 8 - Prob. 62PCh. 8 - Prob. 63PCh. 8 - Prob. 64PCh. 8 - Using the Goodman fatigue criterion, repeat Prob....Ch. 8 - The figure shows a bolted lap joint that uses SAE...Ch. 8 - Prob. 67PCh. 8 - A bolted lap joint using ISO class 5.8 bolts and...Ch. 8 - Prob. 69PCh. 8 - The figure shows a connection that employs three...Ch. 8 - A beam is made up by bolting together two cold...Ch. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - A vertical channel 152 76 (see Table A7) has a...Ch. 8 - The cantilever bracket is bolted to a column with...Ch. 8 - Prob. 77PCh. 8 - The figure shows a welded fitting which has been...Ch. 8 - Prob. 79PCh. 8 - Prob. 80PCh. 8 - Prob. 81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For the lap connection shown, the rivets are 19-mm diameter and the plates are 8 mm thick. The rivets used are A502, Grade 1 and the plates are ASTM A36 with Fu = 400 MPa. Determine the value of Pin all possible modes of failure and the safe value of P that the connection can resist. Fv = 120 MPa, Fp = 1.2 Fu. Add 1.6 mm for the hole diameter. Ans. 297.6 KNarrow_forwardRequired information A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Determine the size of the cross section. The size of the cross section is 24 mm.arrow_forwardProblem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt is chosen made from A307 with rolled threads. Washers are included between the head and the joint, and between the nut and the joint. Determine a suitable length for the bolt? Find its safety factor against yielding and against joint separation. Are these values acceptable?arrow_forward
- A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?arrow_forwardDesign a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.4arrow_forwardThe figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it appliesarrow_forward
- An A-36 steel bolt (AB) is used to snugly clamp a 6061-T6 aluminum sleeve between two rigid platens E and F, as shown below. The bolt has a solid, circular cross section with a diameter d = 61 mm and a thread pitch of 1 mm. The sleeve has a hollow circular cross section with an outer diameter do 250 mm and a wall thickness tw = 15 mm. The nut is then tightened 34 of a turn, which induces stresses in both the bolt and the sleeve. Assume Es = 200 GPa for steel and Ea 68.9 GPa for aluminum. 450 mm F A -250 mm- 500 mm 15 mm (a) Determine the normal stress in the bolt (both magnitude and sign). (b) Determine the normal stress in the sleeve (both magnitude and sign).arrow_forwardThe cantilever bracket Is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket Is made from AISI 1020 hot- rolled steel. Assume the bolt threads do not extend into the Joint. Find the factors of safety for the following fallure modes: shear of bolts, bearing of bolts, bearing of bracket, and bending of the bracket. GIVE the overall jolnt factor of safety. Given: F= 2 KN. NOTE: This is a multi-part questlon. Once an answer Is submitted, you will be unable to return to this part. Holes for M12 x 1.75 bolts 8 mm thick 36 32 36 - 200- Column Find the factor of safety with respect to the shear stress In the bolts. The factor of safety with respect to the shear stress In the bolts ng Is 4.4arrow_forwardA trapezoidal-threaded power screw with a crest diam- eter of 30 mm and single thread is used to raise a load of 50 kN. The collar mean diameter is 40 mm. The coeffi- cient of friction is 0.12 for both the thread and the collar. Determine the following: (a) Pitch diameter of the screw. Ans. dp = = 27.0 mm.arrow_forward
- A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.arrow_forward1. For a bolted assembly with six bolts, the stiffness of each bolt is k, = 3 Mlbf/in and the stiffness of the members is km = 12 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume a torque co-efficient of K = 0.2. a. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts. b. Determine the minimum bolt preload that can be applied while avoiding joint separation. c. Determine the value of torque in units of Ibf-ft that should be specified for preloading the bolts if it is desired to preload to 75% of the proof load. d. Determine the yielding factor of safety for part c). (based on proof strength)arrow_forwardDesign a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are 6. The permissible tensile stress for the bolt material is 90 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3. M45 M42 M39 Choose one of the following solutions: M36 M45,M42,M39,M36,M33,M30,M27,M24 M33 M30 M27 M24arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Stresses Due to Fluctuating Loads Introduction - Design Against Fluctuating Loads - Machine Design 1; Author: Ekeeda;https://www.youtube.com/watch?v=3FBmQXfP_eE;License: Standard Youtube License