Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 8, Problem 12P
An M14 × 2 hex-head bolt with a nut is used to clamp together two 15-mm steel plates.
- (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm.
- (b) Determine the bolt stiffness.
- (c) Determine the stiffness of the members.
8-12 Repeat Prob. 8-11 with the addition of one 14R metric plain washer under the nut.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An A-36 steel bolt (AB) is used to snugly clamp a 6061-T6 aluminum sleeve
between two rigid platens E and F, as shown below. The bolt has a solid, circular cross section
with a diameter d = 61 mm and a thread pitch
of 1 mm. The sleeve has a hollow circular
cross section with an outer diameter do 250
mm and a wall thickness tw = 15 mm. The
nut is then tightened 34 of a turn, which
induces stresses in both the bolt and the
sleeve. Assume Es = 200 GPa for steel and
Ea 68.9 GPa for aluminum.
450 mm
F
A
-250 mm-
500 mm
15 mm
(a) Determine the normal stress in the bolt
(both magnitude and sign).
(b) Determine the normal stress in the sleeve
(both magnitude and sign).
Two plates are clamped by a 3/4-10 UNC SAE
Grade 5 bolt and regular nut with a 3/4-W plain
washer as shown in figure. Top plate is made of
grey cast iron and bottom plate is steel. An axial
force of 12kN is acted upon the joint. Round off
the length of the bolt to nearest 1/4in. Assume
bolts are preloaded to 75% of proof load.
1. Determine the bolt stiffness kb.
2. Determine the member stiffness km.
3. Determine the yielding factor of safety of the
bolt.
4. Determine the load factor for the bolt.
5. Determine the load factor guarding against
joint separation.
1.25 in
1.00 in
Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied
load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof
strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt
is chosen made from A307 with rolled threads. Washers are included between the head
and the joint, and between the nut and the joint. Determine a suitable length for the
bolt? Find its safety factor against yielding and against joint separation. Are these
values acceptable?
Chapter 8 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 8 - A power screw is 25 mm in diameter and has a...Ch. 8 - Using the information in the footnote of Table...Ch. 8 - Show that for zero collar friction the efficiency...Ch. 8 - A single-threaded power screw is 25 mm in diameter...Ch. 8 - The machine shown in the figure can be used for a...Ch. 8 - The press shown for Prob. 8-5 has a rated load of...Ch. 8 - For the screw clamp shown, a force is applied at...Ch. 8 - The C clamp shown in the figure for Prob. 8-7 uses...Ch. 8 - Find the power required to drive a 1.5-in power...Ch. 8 - A single square-thread power screw has an input...
Ch. 8 - Prob. 11PCh. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - Prob. 13PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Repeat Prob. 8-14 with the addition of one 12 N...Ch. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Two identical aluminum plates are each 2 in thick,...Ch. 8 - Prob. 18PCh. 8 - A 30-mm thick AISI 1020 steel plate is sandwiched...Ch. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - An aluminum bracket with a 12-in thick flange is...Ch. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - A 34 in-16 UNF series SAE grade 5 bolt has a 34-in...Ch. 8 - From your experience with Prob. 8-26, generalize...Ch. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - For a bolted assembly with eight bolts, the...Ch. 8 - Prob. 32PCh. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - 837 to 840 Repeat the requirements for the problem...Ch. 8 - Prob. 40PCh. 8 - 841 to 844 For the pressure vessel defined in the...Ch. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Bolts distributed about a bolt circle are often...Ch. 8 - The figure shows a cast-iron bearing block that is...Ch. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - Prob. 52PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - For the pressure cylinder defined in the problem...Ch. 8 - A 1-in-diameter hot-rolled AISI 1144 steel rod is...Ch. 8 - The section of the sealed joint shown in the...Ch. 8 - Prob. 61PCh. 8 - Prob. 62PCh. 8 - Prob. 63PCh. 8 - Prob. 64PCh. 8 - Using the Goodman fatigue criterion, repeat Prob....Ch. 8 - The figure shows a bolted lap joint that uses SAE...Ch. 8 - Prob. 67PCh. 8 - A bolted lap joint using ISO class 5.8 bolts and...Ch. 8 - Prob. 69PCh. 8 - The figure shows a connection that employs three...Ch. 8 - A beam is made up by bolting together two cold...Ch. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - A vertical channel 152 76 (see Table A7) has a...Ch. 8 - The cantilever bracket is bolted to a column with...Ch. 8 - Prob. 77PCh. 8 - The figure shows a welded fitting which has been...Ch. 8 - Prob. 79PCh. 8 - Prob. 80PCh. 8 - Prob. 81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. For a bolted assembly with six bolts, the stiffness of each bolt is k, = 3 Mlbf/in and the stiffness of the members is km = 12 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume a torque co-efficient of K = 0.2. a. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts. b. Determine the minimum bolt preload that can be applied while avoiding joint separation. c. Determine the value of torque in units of Ibf-ft that should be specified for preloading the bolts if it is desired to preload to 75% of the proof load. d. Determine the yielding factor of safety for part c). (based on proof strength)arrow_forwardThe figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load fluctuating between 0 and 13 kN. The members are made from steel. The members have equal thicknesses and total length of members is L=37 mm. Each bolt is initially tightened carefully to 78% of proof load. The bolt is to be Metric grade 5.8 M12x1.75 (coarse-pitch series). The threads has been manufactured by rolling and reliability for bolts is 95%. Calculate the stiffness of the bolt (in kN/mm). Yanıt:arrow_forward34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))arrow_forward
- 1- Name the different forms of journal bearings. 2- Sketch with freehand and name the different types of rivet heads 3- What are the various applications of screwed fasteners ? 4-Why are washers used in bolted joints ? 5- Rigid couplings are used for shafts which are (a) Slightly mis-aligned (b) Inclined (c) Со-ахial 6- The height of hexagonal nut is (а) D (b) 1.1D (с) 1.3D 7- Journal bearings can support only (a) axial loads (b) radial loads (c) inclined loads 8- A key is a temporary joint (True/False). 9- A cotter is a permanent joint (True/False). 10- Taper sunk key is tapered on both sides (True/False). 11- Shaft couplings are permanent in nature (True/False). 12- In zig-zag riveting, the rivets in adjacent rows are placed directly opposite to each other (True/False). -100 Taper 1 in 100 What is kind of shaft coupling illustrated in Figure (1), Draw tow views including one that show in figure where dimension of saddle key are (w=16, T=10mm) Figure (1)arrow_forwardAn M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two 18-mm steel plates. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the bolt stiffness. The bolt stiffness kb is 592.69 MN/m.arrow_forwardQestion-1: A 9/16 in UNF bolt is subjected to a load P = 60 kip in a tension joint as shown in Figure. The bolt is SAE grade 5 and lubricated. The initial bolt tension (F) = 35 kip. The bolt and joint stiffnesses are k, = 6.5 and km 10.8 Mlbf/in Note: Use the related tables, formulas and concepts to answer following question (a) Formulate to determine the preload and service load stresses in the bolt. (b) Solve to find the torque necessary to develop the preload. (c) Identify if the bolt will fail or no under preload and service load stresses (Calculated in part a) by comparing with the SAE minimum proof strength of the bolt. (d) Can you identify; with given input data, tables and formulas that bolt is self-locking? Table 8-9 SAE Specifications for Steel Bolts Size SAE Range Grade Inclusive, No. in +14 1 2 4 5 5.2 7 8 TI I LI I I I +-14 8.2 -1 Minimum Proof Strength," kpsi 33 55 33 65 85 74 85 105 120 120 Table 8-2 Diameters and Area of Unified Screw Threads Size Designation 0 1 2 3 4…arrow_forward
- A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in acyclical fashion as the mechanism runs. It has been decided to use AISI 1040 cold-drawn steel.Complete the design of the link, specifying a suitable cross-sectional shape and dimensions.5. Specify the required length of no. 60 chain to mount on sprockets having 15 and 50 teeth with acenter distance of no more than 36 in.arrow_forwardA bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33 in the textbook of Shigley's Mechanical Engineering Design, 8th Edition) (a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt? (b) What is the length of the grip l? (c) What is the height H of the nut? (d) Is the bolt long enough? If not, round to the next larger preferred length. (e) What is the length of the shank and the threaded portions of the bolt within the grip?arrow_forwardM16 x 2.0 ISO 5.8 coarse series bolts and nuts clamp a 26-mm-thick steel cover plate to a 6-mm-thick steel flange. Steel washers (Size: 16R) are used under the head of the bolt and also under the nut . Assume E = 207 GPa- (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the stiffness of the joint.arrow_forward
- A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt is 3/8 in-16 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest 4 in. (2) Determine the bolt stiffness ks. (3) Determine the stiffness of the members km.arrow_forwardFor a bolted assembly with 8 bolts, the stiffness of each bolt is k_b = 1.1 N/mm and the stiffness of the members is k_m = 2.8 N/mm at each bolt location. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly (to 75% of the proof stress). Assume the external load is equally distributed to all the bolts. It has been determined to use M6 × 1 class 5.8 bolts with rolled threads. Determine the maximum safe working load that both limits the stress in the bolts to be below the proof stress and ensures that the members do not come out of compression. Express your answer in units of kilonewtons.arrow_forwardCalculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License